Admiral Washer Switch

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

• Will not fill with water
• Will not agitate

First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more

• Will not fill with water
• Won't start

No water, no electricity, nothing happened when I pulled the on knob. I replaced the lid switch. The switch arrived at my house super fast - ordered on Friday and was there on Saturday. The whole replacement process took no time at all. Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more

• No hot or cold water

I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more

Ordered the right part, took the back off the top control panel, and popped it in. Read more

I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more

Replaced the motor wax door lock switch and the door lock spin enable switch. Read more

Replaced the water level switch and water level pressure switch hose. Video on AppliancePartsPros.com detailed the procedure. Read more

Replaced with a new one. Read more

I watched the repair video AppliancePartsPros.com had on each repair and followed the instructions. Read more

Filled tub to about 6 inches and inspected washer. Noticed that the tube leading from the air entrapment bubble on the exterior side of the drum had a small leak in it. Clipped off the part of the tube that had the hole in it(it was very close to the connector nipple) reconnected and problem was solved. Read more

I had the problem couple years ago I bypassed unbalance switch it worked fine for a couple years and had the same problem again so ruled out unbalanced switch. Door lock light on and checked made sure wax motor pushed out all the way too the second switch for spin check OK, so took a chance on displacement switch x2. My family loves to over load it and also replaced by passed unbalance switch and boom every thing went back to normal. Its also good to clean every thing when apart. Read more