Yard-Man Parts

Control cable for walk-behind mowers. Connects throttle or self-propel controls to engine or drive system. Replace if cable is broken, frayed, or stretched.

Control cable that connects the auger handle to the engagement mechanism. Replace if cable is frayed, stretched, broken, or detached from the handle.

This air filter consists of an internal plastic frame with a foam mesh cover that captures dust and dirt. The outer, washable pad covers an accordion-style inner filter that removes even finer particles. An air filter keeps particles in the air from getting sucked into the motor, where friction will cause wear and tear to the engine. However, a filter has a limited life cycle. Eventually, it gets clogged up, which leads to limited airflow and decreased efficiency. If the engine is bogging down when it is revved up, a clogged air filter might be to blame. Simply install a new air filter and see if the motor performance improves. It is recommended to preemptively replace the air filter every spring so a clogged filter never puts a halt to a job in progress. This is an OEM part, sourced directly from MTD, and it is sold individually. In addition to MTD lawn equipment, it has also been used by other manufacturers, including Craftsman, Yard Machine, and Yard-Man.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

Trigger handle kit for gas snowblowers. Installs on the control panel to operate auger and drive engagement. Replace if cracked, broken, or missing.

Front wheel assembly for walk-behind mowers. Installs on the front axle to support and guide the mower. Replace if cracked, worn, or broken.

Replacement rear wheel for walk-behind mowers. Installs on axle assembly. Order when original wheel is cracked, broken, or worn for smooth operation.

Replace your worn or damaged 22-inch mulching blade. This lawn mower blade installs under the deck to finely cut grass clippings for mulching.

This axle oil seal is an authentic OEM replacement part sourced directly from the manufacturer for use on lawn tractors. The oil axle seal keeps transmission fluid from leaking and causing damage to the engine. If there are puddles of oil beneath the lawn tractor, the axle's oil seal should be inspected and replaced if necessary. During routine maintenance, the oil seal should be visually inspected, and it should be removed and replaced when there are signs of wear and tear. To replace the axle oil seal, first, remove the spark plug from the machine for safety. Park the lawn tractor on a flat surface to prevent accidental rolling. Wear work gloves and safety goggles. Remove the half shaft from the tractor and pry the old axle oil seal off the machine. Insert a new oil seal. Check the fluids in the lawn tractor and fill as needed, then reassemble the tractor. After putting the spark plug back in, run the engine and look for leaks. This axle oil seal is a black rubber part that is sold individually. It is designed for use on lawn tractors manufactured by Cub Cadet, Yard-Man, MTD, and Troy-Bilt.

Protective shield that mounts over the edger blade to block flying debris and stones. Replace if cracked, broken, or missing for safe operation.

Replacement drive control cable for gas and self-propelled walk-behind mowers. Installs to engage drive system. Replace if cable is broken, frayed, or worn.

Replacement foot pedal pad for lawn tractors and riding mowers. Installs on control pedals. Needed when original pad is worn, cracked, or missing.

Foam handle grip for lawn mowers and tillers. Replaces worn, torn, or missing grips on control handles. Provides cushioned comfort and secure hold.

Replaces worn, dull, or damaged 21-inch mulching blades on walk-behind mowers. Features curved design for effective mulching. Upgrade your rusty blade.