Need Help?
Call or text
Dryer cylinder belt transmits motor power to spin the drum. Replace if belt is worn, frayed, or broken causing drum not to turn. Verify fit with model number.
Third try was a charm!!!! Read more
Fix slow fills, no hot water, or water dripping issues. This dual inlet valve controls hot and cold water flow into your washer tub. Moderate DIY repair.
I replaced both the solenoid (part of the inlet valve kit) and the pressure sensor. Online research suggested my intermittent issue with the cold water fill being just a trickle and then causing an error was likely due to one or both of those two parts failing. Since they are in the same spot it was suggested (and I agree) that it is best to replace both at the same time. The hardest and most frustrating part was getting the bracket back on with the two bottom tabs being in place. It took... Read more
Fix no hot water, continuous leaking into drum, or slow fill issues. This dual inlet valve controls hot and cold water flow during wash cycles.
Replaced water mixing valve. Read more
Dryer blowing cold air or not heating? This limit thermostat monitors drum temperature and controls the heating element. Common fix for temperature issues.
I found a few videos on YouTube about other dryers that gave me enough information to figure out my own. I was able to pull out the heater element and replace it with a new one that arrived the day after I purchased it. I also replaced the thermal fuse and thermostat. Read more
The Knob Assembly is an OEM component specifically designed for Speed Queen dryers. This assembly includes the control knob and integrated electronic components that allow for cycle and setting selection.
Causes of a defective knob assembly include normal wear of constantly rotated buttons, sun damage to exposed plastic knobs, and general use degradation of sealed electronic sensors over time.
Symptoms of a bad knob assembly include:
This OEM Speed Queen part is also compatible with products from American Dryer Corporation. Replacing the entire knob assembly restores full functionality to reliably control cycles on your dryer. Proper maintenance ensures long-term durability.
New timer Read more
Dryer not heating? This heating element generates the heat needed to dry clothes effectively. DIY-friendly repair with moderate difficulty.
Idler lever kit for Speed Queen washers. Maintains belt tension for smooth drum rotation. Replace if lever is cracked, pulley worn, or mechanism damaged.
The belt/Idler kit arrived next day after placing the order. The included directions were very clear with an exploded diagram. Four bolts remove the motor/pump assembly from the machine, three clips release the pump from the motor, then four small nuts remove the support brace from the motor to get access to the pulley and lever. Reverse order to re-assemble. The idler/pulley was in good condition. However, the kit is just a few $ more and replacement was only few extra steps. The worn belt... Read more
If your washer won't start or stops mid-cycle, the lid lock may be faulty. This kit includes the lock assembly and mounting hardware for secure operation.
Fix washer not filling, low water errors, or intermittent fill issues. This pressure sensor monitors water levels and signals the control board. DIY-friendly.
White plastic inner door bezel that mounts inside your washer door to provide structural support. Replace if cracked, broken, or damaged at hinge points.
Speed Queen is out of stock in the washer door for this model and the appliance repair company said it was on back order indefinitely. I had saved the broken door so I ordered the inner plastic liner and the glass separately and used the saved outer door part and the screws and bracket and the mechanism that inserts into the machine itself to lock the door in place and sandwiched everything together and after a few attempts at the correct order of putting it all together, managed to get it... Read more
Maintains tension on the drive belt. Replace if the wheel is cracked, bearing is worn, or assembly is broken to restore smooth, quiet drum rotation.
Changed the drum rollers, belt, and idler pulley wheel. Was not sure which one was making the noise but all three were well used and many years old. One of the drum wheels was the culprit. very easy and straightforward repair with no assistance. Read more
Fix water leaking from the bottom of your washer with a new drain pump. This part removes water at the end of each cycle. Direct replacement, moderate DIY.
I replaced the water pump. Read more
This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.
Pulled the broken knob off and replaced it with the new one. Took about 10 seconds I think...maybe less. Read more
Idler lever assembly with bearing and wheel for dryers. Maintains belt tension for smooth drum rotation. Replace if cracked, worn, or causing squeaking.
Replace idler wheel assembly, belt and spring. Read more
Dryer won't start or stops mid-cycle? A worn door catch prevents secure latching. This assembly holds the door shut so your dryer runs. DIY-friendly repair.
I called a local appliance store that gave us a replacement. That one broke after 1 week! The door was off balance. Tightened screws to realign. I found your store online and ordered the part. Arrived in 1 day! The part is much stronger than the first one. So far so good! Read more
This drum support roller installs inside your dryer to support and guide the drum as it rotates. Replace if cracked, worn, or causing noise during operation.