Cooktop Wire, Harness, Power Cord

This replacement dryer power cord supplies electricity from your wall outlet to the dryer's terminal block, providing a secure, reliable connection. Replace a worn or damaged cord to restore dependable power and reduce risk of intermittent shutoffs.

• Supplies electrical power from the outlet to the dryer
• Provides a secure connection at the plug and the dryer's terminal block when properly installed
• Common fixes: dryer won't power on, power cuts out when the unit is moved, or visible damage/heat discoloration on the cord or plug
• Replace if prongs are loose or the insulation is cracked or melted

• Disconnect power at the breaker before servicing and verify the outlet is de-energized
• Follow the dryer's wiring diagram; connect conductors to the correct terminals and tighten securely
• Use an approved strain relief/clamp per the dryer instructions and local electrical codes

Replacement power cord for gas ranges. Connects your unit to the wall outlet. Replace if cord is worn, cut, heat-damaged, or causing burning smells.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

Replace a damaged, frayed, or worn power cord on your gas range. This 18-gauge supply cord assembly with push-tie strain relief restores safe electrical connection.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

Connects cooktop ignition components for reliable spark delivery. Replace this harness if wires are damaged, frayed, melted, or causing connection issues.

Wire harness with LED assembly that connects an appliance's control circuitry to an LED indicator or lighting module, restoring proper indicator illumination and signal routing when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection and mounted LED used for control/indicator or internal lighting circuits
• Transfers power and signal between the control board and the LED/indicator
• Can correct symptoms such as a dim, flickering, or non-lighting indicator or intermittent LED function
• Replaces a damaged or corroded connector that causes loss of indicator/lighting

• Disconnect power to the appliance before attempting replacement to avoid shock or damage
• Handle connectors and the LED assembly carefully to avoid bending pins or damaging wiring
• Route and secure the harness to match original routing and avoid pinch points or heat sources
• Test operation after installation; for wiring diagrams and connector locations

Wire harness that connects heating elements to your cooktop's internal wiring. Replace if burned, brittle, cracked, or damaged to restore power delivery.

High-voltage wire harness connects power components in your range. Replace if wires are burned, damaged, or failing continuity tests. Restores safe operation.

Connects your range to the wall outlet to supply electrical power. Replace if your original cord is frayed, damaged, cracked, or missing from installation.

Replacement power cord for gas ranges. Installs to restore main electrical connection. Order when original cord is frayed, cut, melted, or damaged.

This single-conductor replacement wire restores an electrical connection between components in compatible Whirlpool appliances. It's a straightforward part used when a damaged or broken wire prevents normal operation. What it does

• Carries electrical current between terminals or components to enable operation.
• Replaces frayed, broken, or heat-damaged wiring that can cause intermittent or no power to a component.
• Common symptom: affected circuit or component won't power on or works sporadically.
• Helps re-establish a reliable connection when the original wire is corroded or has a broken conductor.

• Disconnect power (unplug appliance or shut off circuit breaker) before starting any repair.
• Use proper wire connectors/crimping techniques and ensure secure, insulated connections.
• Verify correct routing and strain relief to avoid contact with moving parts or heating elements.

Replace a cracked, frayed, or missing 3-wire power cord for your electric range. This 4-foot, 40-amp cord restores safe electrical connection.

Replacement power cord for cooktops and ranges. Connects appliance to wall outlet. Install when original cord is damaged, cut, frayed, or missing.