Estate Clip Or Clamp

The Clutch Band and Lining Kit is an OEM part for Whirlpool washing machines. It contains the clutch band and clutch lining components essential for proper transmission of power from the washer motor to its drum during the spin cycle. The clutch band and lining allow for a controlled amount of slippage to safely extract water from clothes without damage. 

Symptoms of a bad clutch band and lining include: 

• Excessive noise or vibration during spin
• Slow or ineffective spinning 
• The drum failing to spin or “locking up”
• Premature wear of other transmission parts

Over time and with heavy use, these components can wear down. If slipping or damage is detected, it’s important to replace the kit to avoid potential transmission repairs.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.

This door spring restores the proper counterbalance of the oven door so it opens smoothly and closes with controlled tension. Replacing a worn or broken spring helps prevent the door from dropping, slamming, or sitting unevenly.

• Provides counterbalance tension for the oven door through the hinge mechanism
• Helps the door open smoothly and hold at a partially open position
• Maintains even alignment and consistent gasket contact
• Common symptoms of failure: door feels heavy, drops open or slams, uneven door height, squeaks during movement

• Disconnect power at the breaker and allow the oven to cool completely
• Springs are under tension—support the door and use caution to avoid injury
• Note the spring's routing and anchor points before removal; reinstall in the same positions
• For even tension, consider replacing both door springs when the design uses one per side

Secures the thermostat sensor bulb in place on your range. Replace if broken or corroded to restore accurate temperature control. Verify fit by model.

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Secures hoses and prevents leaks in dryers, washers, and laundry centers. Replace when connections loosen or drips appear. Verify fit by model.

Secures panels and components in your washer to prevent rattles and maintain alignment. Replace when broken or missing to restore proper fit.

Left hand side. For right hand use 98004953

Secures inner glass panel to oven door liner on electric and gas ranges. Replace if glass is loose or rattling. Verify fit with your model number.

Range clip secures wiring and components. Replace if broken, loose, or missing to prevent rattling and ensure proper part positioning. Verify fit with your model.

Secures wiring harnesses in your gas range. Replace if damaged, loose, or causing electrical connection issues. Verify fit with your model number.

Secures wiring and components to prevent movement and disconnection in your electric range. Replace if clips are broken or wires are loose. Verify fit with your model number.

Secures insulation in your range to maintain proper heat retention and efficiency. Replace if damaged, loose, or missing to prevent insulation shifting. Confirm fit with your model number.