Frigidaire Refrigerator Leg Or Foot

The Crisper Pan is an OEM part for Frigidaire refrigerators. This pan is designed to store fruits and vegetables, helping to maintain optimal humidity levels to keep produce fresh for longer periods.

Causes of a bad crisper pan can include cracks or breaks from accidental impacts, wear and tear from regular use, or warping due to temperature fluctuations.  

Symptoms of a bad crisper pan include:

• Cracks or visible damage on the pan
• Difficulty sliding the pan in and out
• Decreased freshness or spoilage of stored produce
• Leaks or moisture buildup inside the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

Adjustable leveling foot for refrigerators and freezers. Installs at the base to stabilize and level the appliance. Replace if cracked or broken.

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

This replacement drum support roller helps the dryer drum turn smoothly and reduces noise from worn or seized rollers. Restores proper drum alignment for more reliable drying and quieter operation. What it does:

• Supports the dryer drum and allows it to rotate on a stable axle
• Reduces squealing, grinding, or scraping noises caused by worn rollers
• Prevents drum wobble and uneven wear that can lead to fabric damage or belt stress
• Helps maintain proper drum alignment to improve drying performance

• Disconnect power before servicing and ensure the dryer is fully powered off.
• Access may require removing the dryer back panel or front bulkhead; support the drum while replacing the roller.
• Inspect adjacent parts (shaft, felt seals, idler, belt) and replace if worn to avoid repeat failures.
• Tighten fasteners securely but avoid over-torquing; test drum rotation by hand before reassembly.

Replace a damaged, broken, or missing leveling leg to stabilize your refrigerator on uneven floors. Adjustable foot reduces rocking and improves alignment.

Replacement front roller assembly for refrigerators. Includes leveling screw. Needed when roller is cracked, broken, or leveling screw is bent or damaged.

Rear roller assembly for refrigerators. Mounts under the back of the unit to allow smooth rolling and positioning. Replace if cracked, worn, or broken.