Gaggenau Wall Oven Parts

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Door won't lock or difficult to open during self-clean? This oven door latch assembly secures the door and reports lock status to the control board.

This light bu is a genuine Bosch part, sold individually. This light bu can be used as a replacement part for a gas range. This part illuminates the inside of the oven so that its interior can be seen while the appliance is in operation. This allows the user to see the interior without opening the door or visually inspecting the oven from the inside.A light bu will often be subject for replacement at some point in the lifespan of a gas range. This will most likely be due to a light bu losing power over time, but damage can also occur that will necessitate replacement, including cracks, chips, and punctures that can shatter a light bu immediately. If this is the case, the light bu should be removed and replaced with this genuine OEM replacement part. The replacement process will require no special tools. Simply screw the light bu into place.This is an OEM part sourced directly from the manufacturer. It is sold individually. This light bu is compatible with the following appliance brands: Bosch and Gaggenau.

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

Seals your range oven door to retain heat and prevent energy loss. Replace if worn, cracked, or allowing heat to escape. Verify fit with your model.

This door hinge provides the pivot point that lets the appliance door open smoothly and close flush. Replacing a worn or bent hinge restores proper alignment and sealing for safe, reliable door operation.

• Provides the pivot point that guides door opening and closing
• Helps keep the door square to the cabinet for a consistent seal
• Wear or damage can cause sagging, binding, gaps, or a door that won't close flush
• Restores smooth movement and proper door alignment

• Disconnect power before servicing; also shut off gas or water
• Support the door during removal to prevent damage or injury
• Transfer any mounting screws/brackets from the old hinge to the new one
• After installation, verify door alignment and gasket contact; adjust as needed

This is a replacement door handle assembly for Bosch appliances, providing a secure grip and restoring proper door opening and closing. It replaces a damaged, loose, or broken handle so you can use the appliance safely and conveniently. What it does:

• Replaces the exterior door handle so the door opens and closes reliably
• Restores user grip and ergonomic operation after handle damage or wear
• Helps prevent further damage from using a broken or loose handle
• Fits as the OEM-style handle on compatible Bosch doors per parts diagram

• One handle assembly as shown

• High-level: removal of the door trim or access panel may be required; follow your model's service manual
• Use appropriate hand tools and keep fasteners organized to avoid losing small clips or screws
• Disconnect power and follow safety guidance for your appliance before beginning repair

Seals the heating element opening to maintain proper heat and prevent leaks. Replace when worn or damaged to restore efficient operation. Confirm fit.

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

Fix a microwave door that won't pop open when you press the button. This door release lever restores smooth latching action for easy everyday use.

Seals side lamp glass on lawn tractors, blocking moisture and debris from the housing. Replace when glass rattles or leaks occur. Confirm fit with your model.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram

Replace a bent, warped, or missing oven rack. This wire shelf installs inside your oven to provide stable support for cookware and bakeware at the correct height.