General Electric Washer Gasket & Seal

Seals the door opening on front-load washers to prevent leaks during cycles. Replace if torn, cracked, or leaking. Confirm fit with your model number.

Seals washer door to prevent leaks during cycles. Replace if water leaks from door, gasket is torn, or mold persists after cleaning. Confirm fit with model.

Seals the washer door to prevent leaks. Replace if torn, brittle, or leaking. Confirm fit by entering your model number on the product page.

Secures your washer's inner door gasket to maintain a watertight seal and prevent leaks. Replace if the gasket is loose or water escapes during cycles. Confirm fit with your model number.

Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.

Replace your washer tub seal to stop leaks between inner and outer tubs. Install when you notice water pooling or moisture around the drum. Verify fit.

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn, torn, or deformed seal to restore a tight door closure. What it does:

• Creates an airtight seal around the refrigerator door edge to preserve internal temperature.
• Helps prevent frost buildup and condensation by stopping warm, moist air from entering.
• Reduces compressor run time and energy waste caused by a leaking door.
• Restores proper door alignment and magnetic closure when the original gasket is damaged.

• One replacement refrigerator door gasket

• Disconnect power to the appliance before starting any work.
• Clean and dry the door flange thoroughly before fitting the new gasket.
• Start at one corner, press gasket firmly into the channel, and ensure magnetic/retention edges seat evenly around the door.
• If gasket wrinkles or does not seat, warm it slightly or allow time for it to relax; avoid sharp tools that can damage the new seal.

Washer tub hub gasket seals the connection between tub and hub assembly. Replace if leaking during wash or spin cycles. Verify fit with your model.

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

A foam insulation barrier that helps seal and protect refrigerator cabinet cavities from air and moisture intrusion. Replaces worn or damaged foam to support proper airflow and reduce the risk of frost buildup around internal components. What it does:

• Provides an insulating seal between cabinet panels and service openings
• Helps limit warm air ingress that can cause frost or reduced cooling performance
• Cushions and isolates components to reduce vibration noise
• Restores original fit where foam has deteriorated or been removed during repairs

• Disconnect power to the appliance before starting any repair
• Remove surrounding panels as needed to access the foam location
• Clean and dry mounting surfaces before applying; use adhesive if required by OEM instructions
• Avoid compressing or blocking vents and airflow paths during installation

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Replace your washer door bellow to prevent leaks and restore a watertight seal. Essential when torn or showing wear to protect against water damage.

This door gasket is the flexible sealing strip that mounts around a refrigerator door to keep cold air in and warm air out, helping maintain temperature and reduce energy use. It restores a tight door seal for proper cooling performance. What it does:

• Seals the door edge to prevent warm air infiltration and cold air loss
• Helps reduce frost buildup and prevents moisture leaks into the compartment
• Supports consistent internal temperature to protect food freshness
• Common symptoms of a failing gasket: visible gaps, torn or flattened seal, cold/temperature fluctuations, excess frost or condensation

• High-level: remove the old gasket, align and seat the new gasket into the channel around the door; some models use screws or retainers
• Safety-first: unplug the appliance or disconnect power before attempting removal/installation
• Handle carefully to avoid tearing; warm the gasket slightly to help fitment if needed
• Refer to your model's service manual or OEM instructions for model-specific steps and fastener locations

Replace your washer's air chamber ring gasket to prevent leaks and restore proper pressure regulation. Ensures reliable operation and water-tight seal.

This oven door gasket provides a replacement seal that helps keep heat and cooking odors inside the oven for consistent cooking and improved efficiency. It restores a tight seal where the door meets the oven cavity. What it does:

• Replaces a worn, torn, or brittle door gasket to reduce heat loss and hot spots
• Helps the oven reach and maintain set temperatures more consistently
• Minimizes smoke, burning smells, and excess energy use caused by leaks
• Improves cooking performance by restoring a proper seal around the door

• One oven door gasket

• Disconnect power to the range/oven before beginning any repair
• Allow the oven to cool completely; remove the oven door per the manufacturer's instructions if required
• Gasket typically attaches by pushing into a channel around the door or oven frame; use a non-marring tool if needed
• Follow OEM instructions for reinstallation and torque recommendations

Plastic seal for washers. Replace when you notice water leaks, moisture around connections, or worn sealing surfaces. Verify fit with your model number.