Kenmore / Sears Tank Or Reservoir

I had a slow leak at the water inlet valve where the water line from the filter assembly connected to the water inlet valve. I determine that the water line had scratches in it which caused it to not seal. Had to buy the entire reservoir and filter assembly to get that water line. The replacement was smooth. It took about 30 minutes to swap out and it fixed the leak. Read more

• Leaking

Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

• Leaking

I replaced to offending part. The only minor issue was that the replacement part had changed design from the original. Otherwise it was a pretty straight forward operation. Read more

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

Almost ordered solenoid valve but realize ice maker was working ok and water dispenser worked good for the first 1-2 seconds. Read online forums and found some posting about replacement of filter head w/ reservoir tha ressembled the problem I was having. Ordered filter head and got part within 2 day (even with ground shipping request). Took about an hour to carefully figure out how to remove covers and install part. An easy way to determine if solenoid is ok is removing filter and installing... Read more

The storage device for water had a cracked fitting so when either the water or ice solenoid was activated the water ran into the compartment. I replaced the storage device (reservoir) once I figured out how to remove the upper cover in the top of the refrigerator. I needed to remove two screws located by the water filter these are the only fasterners needed to be removed, after that you need to pry down on the entire cover which is snapped in place, disconned the electrical connections and your... Read more

Replaced the entire part with new side drawer support. Worked great! Should have done it sooner. Read more

Replaced water reservoir, filter assembly, and water line via the provided instructional videos. The only problems I had where that the water line video had a different fridge layout (filter assembly was perfect), and the inevitable leak on one of the sharkbite-style connectors. I dread dealing with plumbing leaks, so I work on it a little, come back to it the next day, get a little further, etc. Read more

This part was easy to install by following the directions from other users here. As long as you get the right hoses connected in the right places, everything else was straight forward. Takes a few minutes for the tank to initially fill and pressurize and clear the air in the line and then you're on your way to clean fresh water! Read more

• Leaking

I watched your video on YouTube and it was super easy after that, thank you for making this video. Read more

I had to replace all the water lines and valves because they were cracked or just simply blown apart. This last part was the final piece (and the most expensive) to get it back up and running. Tried going the cheap route and purchased waterline from another site that claimed the tube diameter was the same as what i needed, got the line installed it and had waterfalls everywhere (nice mess). The cheap line was 2/1000 of an inch too small and didnt seal in the quick connects. Was not happy, so... Read more