Maytag Washer Hinge Parts

Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

Right hand side. For screws use WPW10119828.

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

This hinge guide is the small bushing the hinge pin rides in. It reduces friction and keeps the panel aligned so the door or lid opens smoothly and closes flush for reliable everyday use.

• Provides a low-friction bearing surface for the hinge pin
• Helps maintain door/lid alignment so it closes flush
• Wear can lead to sagging, scraping, squeaking, or binding
• Restores smooth operation and consistent closing when the original is worn

• Disconnect power; shut off water supply
• Support the door or lid before loosening hinge fasteners
• Remove the worn guide and install the new guide on the hinge pin or in the hinge bracket
• Reassemble, then check alignment and smooth open/close

This hinge secures and guides a refrigerator door on its pivot, helping the door open and close smoothly while maintaining proper alignment and seal. It's a direct-fit replacement when the original hinge is worn or damaged. What it does:

• Replaces a worn or broken door pivot to restore proper door movement and alignment
• Prevents sagging or binding that can stop the door from closing fully
• Helps maintain an effective door seal to protect cooling performance
• Works as the mechanical mounting point between the door and cabinet

• Basic hand tools are typically required; support the door while removing and installing the hinge
• Follow manufacturer guidance for torque and alignment; adjust door leveling as needed after installation
• Disconnect power and remove contents from the door if required for safe handling

This door hinge replaces a worn or damaged refrigerator door pivot to restore smooth opening and secure door alignment. It provides a stable mounting point so doors open and close without sagging or binding. What it does:

• Supports the refrigerator door and keeps it aligned on the cabinet
• Enables smooth pivoting action for opening and closing the door
• Commonly used to fix door sag, sticking, rubbing, or uneven gaps
• Works with original mounting hardware locations to maintain correct seal

• Unplug the appliance or disconnect power before starting work
• Remove food and secure the door; have a helper support the door during removal/installation
• Use basic hand tools; avoid over-tightening fasteners to prevent damage
• Check door alignment after installation and adjust as needed for a proper seal

The Lid Hinge is an OEM part for Whirlpool washers. It is specifically designed to be the left-side hinge for the washer lid, allowing for smooth opening and closing of the lid. The lid hinge ensures proper alignment and stability of the lid, providing easy access to the washer drum.  

A bad lid hinge can occur due to regular wear and tear, accidental damage, or mishandling. If you notice symptoms such as the lid not closing properly, difficulty in opening or closing the lid, or excessive movement or wobbling of the lid, it may be time to replace this part.

Symptoms of a bad lid hinge include:

• Lid not closing properly
• Difficulty in opening or closing the lid
• Damaged spring

Restore your Whirlpool washer's lid by replacing the worn or damaged lid hinge with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement refrigerator door hinge keeps the door aligned and operating smoothly so your appliance seals and closes properly. It restores proper door movement and helps prevent drafts and uneven wear. What it does:

• Supports the refrigerator door and maintains correct alignment for a tight seal
• Allows smooth opening and closing of the door without binding
• Helps prevent door sag, rubbing, or gaps that can cause temperature issues
• Fits where the original hinge mounts to the cabinet or door depending on model

• Disconnect power and remove contents from the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the original fasteners or OEM-recommended hardware; tighten screws securely but avoid over-torquing

This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:

• Replaces a damaged or bent door hinge to correct misaligned or sagging doors
• Restores smooth hinge movement for easier opening and closing
• Helps the door seal properly to maintain internal temperature and efficiency
• Prevents rubbing or binding that can damage door gasket or cabinet finish

• Disconnect power to the appliance before beginning any repairs to avoid injury
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow for correct alignment and torque
• After installation, check door alignment and gasket contact; adjust as needed

Replacement lid hinge for top-load washers. Attaches the lid to the cabinet, allowing smooth opening and closing. Order a new hinge if yours is cracked or broken.

Replace your washer's hinge when cracked, broken, or worn. This structural component supports the lid or door assembly during opening and closing.

Replacement washer lid hinge that connects and supports the top lid. Needed when the existing hinge is cracked, broken, or no longer holds the lid properly.

Secures and guides your washer door for smooth opening and closing. Replace when the hinge is cracked, broken, or worn, causing door misalignment or sagging.