Kenmore Range 790.15032500 (79015032500, 790 15032500) Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 316075103
Oven won't heat or bake properly? This bottom bake element converts electricity to heat for even baking. Simple DIY fix—2 screws, 2 wire terminals.
Do-It-Yourself Stories from Customers like You
Bake element caught on fire and burned until it broke apart at one spot Steve M. • Merritt Island , FL • July 04, 2014
It took no time to find where the problem was! I got my Frigidaire model number and got on-line with AppliancePartsPros.com where I have gone for over a decade for all my household repairs. Why? because they are honest, helpful, considerate, fast, and its easy to locate and SEE the exact part I need. 10 minutes after the burning of my element, one was in my cart and ordered! Done. TWO days later, the part arrived. I turned off the circuit breaker, unscrewed the two 1/4" screws and pulled off...
Read more
More
$35.95
- Compare At:
-
$42.78
- You Save:
-
$6.83
Genuine Frigidaire part
By: Frigidaire
Part Number: 316436000
Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Surface switches not operating properly; going from cool to very hot etc Guy G. • Guthrie , OK • October 10, 2014
Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros.
Read more
More
$60.52
- Compare At:
-
$71.41
- You Save:
-
$10.89
Genuine Frigidaire part
By: Frigidaire
Part Number: 316203200
Oven won't broil or heats unevenly? The broil element provides high heat from above for browning. DIY-friendly repair, usually takes 10 minutes to replace.
Do-It-Yourself Stories from Customers like You
Oven wouldn't heat up Danielle B. • Virginia Beach , VA • March 17, 2015
Removed the bake element and broil element. Tested them with a multi meter. They failed. Ordered new elements. Received them in 2 days. Installed new elements. Oven works great. Entire fix took 10 minutes to remove and test elements, 10 minutes to install the new elements. It was my first time working on an appliance, the instruction videos were great!
Read more
More
$120.52
- Compare At:
-
$142.21
- You Save:
-
$21.69
Genuine Frigidaire part
By: Frigidaire
Part Number: 318178110
Burner not heating? This 6-inch surface heating element restores cooktop function. DIY repair in 10-30 minutes with basic tools and simple instructions.
Do-It-Yourself Stories from Customers like You
Oven surface element went bad Shahlokh K. • Van Nuys , CA • September 21, 2014
Very easy. go online learn how to change the element step by step. order the part and you are all set. I saved $99 of labor cost.
Read more
More
$110.55
- Compare At:
-
$131.55
- You Save:
-
$21.00
Genuine Frigidaire part
By: Frigidaire
Part Number: 316490001
Fix F10 error codes and inconsistent oven temperatures with this sensor probe. Monitors internal temp for accurate cooking. Moderate DIY repair.
This part fixes the following symptoms
-
Oven is too hot
-
Little to no heat when baking
-
Won't start
-
Oven not heating evenly
See more...
Do-It-Yourself Stories from Customers like You
Oven temperature was not consistant and varied at the same setting Robert T. • Palm Beach Gardens , FL • October 13, 2014
I replaced the probe which is a thermocouple. Naturally the connector was different from the one on the stove so I cut off the connector on the old probe and soldered it to the new probe. The cleaning of the wires and soldering them was the most time consuming activity of the repair.
My wife just tried the stove and the oven temperature read exactly as the setting.
Read more
More
$59.48
- Compare At:
-
$70.78
- You Save:
-
$11.30
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303935086
The Surface Unit Switch Kit is an OEM part for Frigidaire ranges. It controls the power and heat levels to the surface burners on the cooktop, allowing you to adjust the temperature for cooking. This kit typically includes the necessary components to replace a faulty switch and restore proper functionality to the burners.
Causes of a bad surface unit switch can include electrical malfunctions, wear and tear from regular use, or damage due to spills or impacts. A faulty switch can prevent the burner from heating correctly or at all.
Symptoms of a bad surface unit switch include:
- Burners not heating up or heating unevenly
- Inability to adjust the burner temperature
- Burners not turning on or off properly
- Sparks or electrical odors near the switch
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My kenmore electric range burners were constantly on high Eric M. • Long Beach , CA • January 23, 2017
When I called customer service your representative at Appliance Parts Pros was able to help me diagnose the problem and order the two parts that I needed. both parts arrived the next day and with helpful tutorial videos I was able to replace both the Surface Unit Switch and the Universal Element in less than 45 minutes.
Thanks so much for the great service and the money you saved me.
Read more
More
$46.35
- Compare At:
-
$55.16
- You Save:
-
$8.81
Genuine Frigidaire part
By: Frigidaire
Part Number: 316022500
Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
A burner switch went bad in our electric stove and an indicator light burnt out Steve G. • Hanover , PA • January 05, 2015
The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should.
Read more
More
$58.43
- Compare At:
-
$69.53
- You Save:
-
$11.10
Genuine Frigidaire part
By: Frigidaire
Part Number: 316407402
Rear glide attaches to the back of your range storage drawer, allowing smooth sliding motion. Replace if broken, cracked, or missing to prevent drawer tilt.
Do-It-Yourself Stories from Customers like You
Range pan drawer dropped to the floor when the drawer was opened Stephen C. • Columbia , MO • May 18, 2014
The clips on the rear side of the drawer box were broken. Easy to locate the part on the website. Part in hand in two days and installed in about five minutes. Needed to remove the drawer and use a 1/4" driver, remove the broken slide and install the new one.
Read more
More
$12.95
- Compare At:
-
$15.54
- You Save:
-
$2.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 807047102
Supports smooth drawer movement in your range's storage compartment. Replace when drawer becomes crooked, slides too far, or glide shows wear grooves.
Do-It-Yourself Stories from Customers like You
Original piece broke off. Jessica S. • Plantation , FL • January 15, 2019
Attaching and screwing the piece, very easy fix.
Read more
More
$16.75
- Compare At:
-
$20.10
- You Save:
-
$3.35
Genuine Frigidaire part
By: Frigidaire
Part Number: 316405000
Replace your electric range oven door seal when compressed, frayed, or heat escapes. Maintains temperature for efficient cooking. Verify fit by model.
Do-It-Yourself Stories from Customers like You
Too much heat escaping the door Michael K. • Mechanicsville , VA • June 22, 2016
Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension.
Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end...
Read more
More
$103.51
- Compare At:
-
$132.23
- You Save:
-
$28.72
Genuine Frigidaire part
By: Frigidaire
Part Number: 316419134
Covers and labels control panel buttons on your range. Replace if the overlay is cracked, peeling, faded, or worn, making buttons hard to read or use.
Do-It-Yourself Stories from Customers like You
Control module going out James C. • Fairlawn , VA • March 08, 2019
Well, after searching for a model number on the range, had to pull the existing module for the part number. Ordered and was shocked to see it arrive the very next day (no, didn't pay for next day). Went back together a lot quicker then me taking apart!
Read more
More
$47.41
- Compare At:
-
$56.89
- You Save:
-
$9.48
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304509869
Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.
Do-It-Yourself Stories from Customers like You
No leveling leg on display model stove I purchased Stephen F. • Rutherfordton , NC • July 28, 2019
Bought new leveling leg. Took longer to lay the appliance on the side and pick back up, than to install leg.
Read more
More
$13.95
- Compare At:
-
$16.74
- You Save:
-
$2.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 316575500
Frames your range's ventilation opening. Replace if cracked, discolored, or missing. Installs around vent area for a finished appearance.
Do-It-Yourself Stories from Customers like You
Kenmore oven plastic on door melted during cleaning cycle oven bottom cracked enamel Anna G. • Lake Zurich , IL • January 18, 2016
Had to order new plastic panel, scared to run the clean cycle again.
Read more
More
$81.41
- Compare At:
-
$97.69
- You Save:
-
$16.28
Genuine Frigidaire part
By: Frigidaire
Part Number: 318198834
The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt
Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.
Symptoms of a bad Surface Element include:
- Not heating up, indicating it may be burnt out or disconnected.
- Heating irregularly or only partially, suggesting there might be damage to the element.
- Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Element was burned out Clayton M. • Demopolis , AL • December 16, 2018
Changed element
Read more
More
$134.95
- Compare At:
-
$160.59
- You Save:
-
$25.64
Genuine Frigidaire part
By: Frigidaire
Part Number: 316112005
Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.
Do-It-Yourself Stories from Customers like You
Missing anti tip bracket. Chip M. • Coconut Creek , FL • June 08, 2019
Installed the new bracket as per instructions with template enclosed and it was perfect.
Read more
More
$17.95
- Compare At:
-
$21.36
- You Save:
-
$3.41
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303935318
Restores the finished look around your range door perimeter. Replaces cracked, discolored, or rusted trim that frames the door and secures outer components.
Do-It-Yourself Stories from Customers like You
An individual did not want to tie his stove down when he was transporting it because of the travel distance because he made a sudden turn the stove fell over breaking the glass front and framework David P. • Henderson , TX • January 29, 2015
Replaced the door trim by removing the 2 screws holding the oven handle on, then removing the 4 screws across the bottom of the door. lifted off the door trim with the plastic door cap. removed the door trim from the cap by sliding it out. attached the new door trim with the 4 screws that had been removed before. then slid the new glass into place. next i slid the plastic door cap onto the new door trim and the glass and centered the glass evenly over the door trim. finally reattached the...
Read more
More
$68.95
- Compare At:
-
$82.74
- You Save:
-
$13.79