Kenmore Microwave 721.89542590 (72189542590, 721 89542590) Parts

Replace your burned-out microwave light bulb to restore clear visibility inside the cavity or over the cooktop. Confirm fit with your model number.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This thermostat controls refrigerator temperature to help maintain proper cooling and prevent spoilage. It replaces a failed or inaccurate temperature control to restore consistent operation. What it does:

• Senses internal temperature and signals the compressor to cycle on/off
• Helps keep food at steady, safe temperatures when functioning correctly
• Commonly replaces thermostats that cause warm temperatures or inconsistent cooling
• Works as a direct replacement when matching the OEM part number

• Always disconnect power to the appliance before servicing to avoid shock or injury
• Handle the sensor and terminals carefully; avoid bending or damaging components
• Basic hand tools are typically required; follow your model's service manual for exact instructions

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

A direct-replacement circulating motor that moves air inside the refrigerator cabinet to help maintain even temperatures and consistent cooling. Replacing a worn motor restores airflow and can reduce warm spots and uneven cooling. What it does:

• Drives internal airflow to distribute cold air between compartments for more uniform temperatures.
• Restores circulation when a failed motor causes weak or no airflow.
• Common, safe-to-report symptoms: uneven cooling, warm spots in the fridge, the appliance running more than usual, or unusual humming/noise from the cabinet.
• Works with the appliance's wiring harness and mounting system to deliver continuous air movement while the cooling system runs.

• Always unplug the appliance before beginning service to avoid electric shock.
• Handle the motor and fan blades carefully to avoid bending or damage; keep fingers and tools clear of blades.
• Confirm correct connector orientation and secure mounting to prevent vibration or rubbing.
• After installing, power up briefly to verify the motor runs and the fan spins freely before reassembling panels.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Button spring for microwave control panels. Replace when buttons feel unresponsive or stick. Verify your model number for proper fit before ordering.

Microwave won't heat but runs normally? This magnetron generates microwave energy to cook food. Requires high-voltage safety knowledge to replace.