Poulan String Trimmer Parts

Engine piston kit for gas trimmers and outdoor equipment. Replaces worn, damaged, or corroded pistons that cause poor compression and engine performance.

This clutch cable kit is an authentic OEM replacement part for a riding lawn mower or tractor. The clutch cable connects to the idler arm located in the lower deck of a mower and allows the operator to manually engage or disengage the blades. The clutch cable runs up through the steering block and into the front display so that the operator can easily access the clutch. If a clutch cable becomes jammed or tenses up, it will be difficult to depress. If the operator tries to depress the clutch cable without realizing that it is jammed, the clutch cable will snap. The most obvious sign of a snapped clutch cable is that the clutch gives little resistance and the blade cannot be engaged. To change a clutch cable, use a socket set to remove the fuel tank and gain access to the cable. A pair of needle nose pliers is also recommended. This replacement part is compatible with Weed Eater, Husqvarna, Ryobi, and Poulan appliances and comes sourced from its original manufacturer. This part includes a clutch cable and a zip tie.

Flanged hex nut for lawn tractors and outdoor power equipment. Replace if threads are stripped, nut is missing, or hardware has corroded or loosened.

Recoil spring for gas and grass line trimmers. Holds the pulley in place and assists with starting mechanism. Replace if damaged, broken, or worn out.

Ignition module for chainsaw engines. Installs on the engine block to control spark timing. Replace if cracked, damaged, or corroded terminals affect ignition.

If your trimmer won't start when you pull the cord, worn starter pulley teeth may not be engaging the flywheel. This kit restores reliable starting.

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

Blocks dirt and debris from entering your trimmer engine. Replace when clogged or worn to restore proper airflow and prevent rough running or starting issues.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Ignition module for gas leaf blowers and trimmers. Works with flywheel to create spark timing. Replace if damaged by heat exposure or engine won't spark.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Replacement fuel tank for front-engine lawn tractors and riding mowers. Installs to store fuel. Replace if cracked, damaged, or leaking.

Foam air filter prevents dirt from entering your trimmer's carburetor and engine. Replace when clogged or washed multiple times. Confirm fit with model.

Shoulder bolt that attaches the suspension arm to the wheel bracket on riding mowers and tractors. Replace if bolt is stripped, worn, or missing.

Starter won't pull freely or rope doesn't retract? This recoil starter spring retracts the pull cord and activates your engine. Simple DIY repair in minutes.