Mark December 14, 2022 for Model Number FAFW3577KW1 Runs till the end of the wash cycle, then stops on beginning of spin cycle. Err 45. Spin only, pump starts, then shuts off immediately, same Err. Diagnosis is to replace the "console control board" I just want to verify that your part AP4362529 is the part they are talking about. Thanks in advance, Mark Heyer
1 Answer Mark, Based on the model number provided this would be the board referenced. 137007010 Read More...
Willie August 12, 2019 for Model Number FAFW3577KR1 I got code e5e. Washer turns on add washes for a minute then shuts back off.
1 Answer Willie, this is going to indicate a communication issue between the main control 137007010 and the speed control board 5304504863. The first thing that will need to be inspected is the wiring to ensure there are no breaks and that the connections are secure and making contact. If the wiring checks good, the next step would be to replace the main control based on the fact that the unit will shut off as quickly as it does. Read More...
Jeffrey December 13, 2018 for Model Number fafw3577kr1 Keep getting error code e31--pressure sensor not communticating with the control board. I've replace the pressure sensor. No change. I suspect I need to replace the control board, but before I order a new one, is there anything else to try?
1 Answer Jeffrey, Check the pressure hose to make sure that the hose is not clogged causing the sensor to not register. If this checks ok then check to make sure that the wiring between the board and the pressure switch is good. If all this checks ok then the control board would be the issue. Read More...
Larry March 28, 2017 for Model Number FAFW3577KA1 Frigidaire washer begins to add water at start but stops. Generally have to keep restarting machine before it finally continues the cycle. Sometimes cancelling and restarting works also. After getting the washer to continue and finish the first load of clothes, the following loads seem to operate normally. The next wash day brings on the problem again.
1 Answer Larry, In most cases this issue will be caused by a faulty user interface control board which is part number 137007010. Read More...
Monica March 02, 2017 for Model Number FAFW011LW0 My washing machine no longer allows me to choose spin or water temperature options. Is this the correct item?
1 Answer Monica, This issue would be the control board which would be part number 137035240NH. Read More...
1 Answer Hello Sarah. You will need to check for loose connections. If the connections are good, then you will need to replace the control board on the unit. Read More...
Ever Z March 28, 2015 for Model Number LAFW3577KW0 When I set my washer on a QUICK cycle it seems to work properly, but when I set it on any other cycle it does not finish the cycle and it just stops *(PAUSE) that’s what read on the digital panel. The washer spins and I get water flow but sometimes it leaves the cloths to wet because it does not complete the cycle.
1 Answer Ever Z., With the unit pausing during the cycle you will want to access the tech sheet and put the unit into a diagnostics and see if there are any fault codes that are stored. If there are then check the tech sheet to see what the error would represent. Read More...
Raa February 10, 2015 for Model Number FAFW3577KA1 Fridgidaire Affinity Front Load Washer Throwing a E90 code on display. Was able to unplug and plug back in and it ran fine for one load, then threw code again. I don't want to keep doing these things to get my washer to work. E90 code is not specifically in manual. Does this indicate to replace main control board (large one) or small control unit (daughter board attached to main control)?
1 Answer Hello RAA. Yes, you will need to order and replace the control board 137007010 on the unit. Read More...
Jim May 12, 2014 for Model Number Frigidaire Washer model FAFW3577KW1 Machine completes wash cycle and the pump comes on to start the spin/drain cycle. A small amount of water comes out then the drain pump loses power and shuts off. The pump works as it should before power shuts off. Is it a control panel?
1 Answer Hello Jim, Check the voltage at the pump terminals. If it is there, (120Vac), replace the pump 137221600 after verifying there is nothing in the tub that could be sealing off the flow of water. If the voltage is not there, then the issue could be the control board 5304504863. Read More...
Michelle December 30, 2013 for Model Number FAFW3577KR1 We have replaced the door switch assembly and the washer will not start now. The code E41 comes up when you push the start/cancel buttons at the same time. Will this part fix the problem
1 Answer Michelle, If you replaced the door switch assembly 134813660 and didn't notice any damaged wires or connections, then Yes the control board 137007010 would be the next likely issue, " E41- Control board thinks the door switch is open." Apparently the control board is not seeing the door switch circuit. Read More...