Virg March 15, 2017 for Model Number WM2016CW the door won't lock .I replace the door switch and door latch. It started door locked then stopped. de message again. Which control board do I need? The de has been a problem for a few years, I can't use the sturdy or normal mode
1 Answer Virg, This issue would be caused by a faulty main control board part number EBR32268001. Read More...
Alex February 26, 2017 for Model Number WM2016CW Washer stop working in the middle of a cycle. No lights at all. Check that power comes to the main control board. Black wire between Main and display boards was broken, solder it but still not working. No lights at all. When pushing power bottom, red light in the main control board comes on for a 3 seconds then off. Which of the boards needs to be replaced?
1 Answer Alex, The main control board sounds like it would be the issue with the unit. It would be recommended to replace the main board and the wiring harness. Read More...
Joe October 13, 2016 for Model Number wm2801hla My washer freezes after it completes the cycle. What would cause this to happen, and what part do I need to replace ?
1 Answer Joe, Since the washer works once it's reset the most likely issue is a "glitch" in the user interface/ display board assembly EBR61020701. You want to check and make sure there aren't any loose connections, unplug and re attach the connectors between the two boards, If the problem persists, replace the display board assembly. The part is in stock and available at this time. Thanks Read More...
Sammie August 22, 2016 for Model Number LG WM2016CW After thumping an unbalanced load last week, my washer stopped working. Took it apart and saw that there was fraying in the wires coming from the main power board to the control panel. Replaced the wires with a new set, but still having the same problem. Machine will beep when I press the power button, but no lights come on in the display. Do you think a new control panel will fix this? Could the problem with the wires have affected the control panel?
1 Answer Hello Sammie. Test for power to the board. If it is there, then replace the board. It is possible the wires shorted the board in the unit. Read More...
Tom January 14, 2016 for Model Number WM2016CW I am not getting hot or warm water in my LG washer (model WM2016CW), I replaced the hot water fill valve but it didn't help. The washer works fine if we use cold water cycles. What else could cause this problem? Bad PCB?
1 Answer Hello Tom, You will need to run the QC test mode. The washer must be empty and the controls must be in the off state. 1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously. 2. Press the Power button, while in the above condition. Then buzzer will sound twice. 3. Press the Start/Pause button repeatedly to cycle through the test modes. The tech sheet goes into detail on the procedure and interpreting the fault codes. It should be located behind the kickpanel. While the hot water valve 5220FR2006H is the first suspect, the control EBR32268001 can also cause this complaint. Read More...
Kerry March 29, 2015 for Model Number WM2016CW How do you remove the main silver knob on the front interface without damaging the interface control panel behind it. When I pull it doesn't seem to want to come off. Thanks!
1 Answer Kerry, To remove the control knob you would want to take the control panel off and remove the control board from the unit. This should allow the knob to come off. Read More...
Dana September 04, 2014 for Model Number WM2077CW Hello, my LG front load washer is starting to develop button problems, are the machines circuit board specific or generic, I would solder in new switches if I knew what they were. Thanks Dana
1 Answer Hello Dana. They are specific. Your board 6871EC1116C has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Jim January 22, 2014 for Model Number wm2050cw I went to use the washer but nothing came on. I changed the main pcb & door switch but still nothing. I have power coming in on power supply cord. Could it be the control?
Joe April 29, 2013 for Model Number lg washing machine wm2016cw The start button isnt working. All the other buttons are working took out the panel ebr32268101. Is there a switch for the on button or do I need the whole panel?
1 Answer Hello Joe. The start is part of the PCB assembly EBR32268101. Just make sure the button is not broke on the unit. Read More...
John R March 05, 2011 Is this part something I could install myself, it looks pretty basic? Does it come with any instructions
1 Answer Hello John. It is a little tricky removing the control panel. Once the panel is removed, it is easy to do. There are no instructions with the part, but if you remove the top of the machine, and the screws holding the control panel on, it is not to hard to do. Hope this helps. Read More...