Bonnie July 10, 2019 for Model Number MAH8700AWW serial 11280453GP My Maytag front load washer has a E3 error. Service man said I need a new control panel but the part is no longer available. Are there a compatible part or was my error misdiagnosed?
1 Answer Bonnie, the error code E3 is going to indicate an error with the motor sensor built into the motor. With this, it can either be a failure in the motor WP34001437, a failure with the main control 34001498, or a break in the wires. The wires can be checked for any break and can be repaired. However, if the wires are in good condition, the motor and control are discontinued parts and are no longer available. As the manufacturer has not listed an approved substitute for these parts, an alternative could not be recommended nor guaranteed to operate properly. Read More...
Tran December 03, 2018 for Model Number MAH8700AWW My Maytag Neptune washing machine just totally dead. How can I figure it out what's wrong? Thanks!
1 Answer Tran, Power comes thru the noise filter when enters the machine. It is possible this is your issue. You need power in and out of the filter or the machines dead. Unfortunately, this part is no longer available. Read More...
Ernie August 14, 2017 for Model Number Maytag MAH8700AWW Is the Whirlpool control board, part# AP4044795, the correct replacement part for my Maytag washer, Model# MAH8700AWW, Ser# 17819308JL?
1 Answer Hello Ernie! Unfortunately the manufacturer has discontinued the board for your series and did not provide a replacement to take it's place. Sorry! Read More...
Rwilson March 24, 2016 for Model Number MAH8700AWW Replaced the motor last August, pump in February and the control board 2 weeks ago. Washer was working on Sunday am then Sunday afternoon the E3 code came on as soon as I start washer. Any ideas?
1 Answer Hello Rwilson. Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving. (Locked, Hall Sensor fault). If motor is good, and tub is not locked up, replace the control board. Read More...
Johnny O January 14, 2016 for Model Number MAH8700AWM Need to verify which control panel assembly is needed for serial number 16214394JE please. One for the 8700 (AP4044795) shows out of stock, but says it will ship in 5-6 days, just need to know if that is the correct one as there are three part numbers shown for item number 5 on that diagram. Much thanks
1 Answer Hello Johnny. Yes, 34001498 shows to be the correct one for your model and serial number. Read More...
Michael October 11, 2015 for Model Number MAH8700AWW- Ser = 10309781GE Sometimes gets nd code. Press the start button and it sometimes will then drain. Eventually it will drain if left long enough. Pump and in/out hoses all clear.
1 Answer Hello Michael. You will need to order and replace the drain pump if it is not clogged. Read More...
Joel September 07, 2015 for Model Number Maytag MAH8700AWW Serial # 12224707GR Hi Guys: I replaced my main control board with #34001495 as you suggested (including the mems sensor). My 2005 machine did NOT have a mems sensor and max spin was 1100 RPM. It seems that even with a perfectly balanced load the spin maximum is now 900 RPM. Is this the correct max speed or is this sensor more sensitive than I am to vibration? Thanks again!
1 Answer Hello Joel. The new boards are programmed with a spin speed of about 900 RPM. It is working properly. Read More...
John G. August 10, 2015 for Model Number MAH8700AWW The serial # 17825669jl. I did the drain pump test on the washer. I do not have 120v at pin 1 of CN5. But I do have it at pin 6 of CN10. Does this mean I need a new control board? If so which one and when do you expect them in if it is out of stock? Original issue was nd. Have a new pump..did not change no drain issue.
1 Answer Hello John. During drain check voltage at Pin #1 of CN5 and Pin #6 of CN10. If it is not there, replace the board. At this time there is no estimated time of arrival of the part. Read More...
Joel August 09, 2015 for Model Number Maytag MAH8700GR Serial # 12224707GR The machine is totally dead. There is power to the machine and to the control board. We had a power outage a few days earlier and the board shows no obvious sign of any burning. What is the proper part number for the control board? Thank you
Herb May 21, 2015 for Model Number Mah8700AWW Serial #17819003jl I own a Maytag neptune front load. I replaced the drain motor due to the propellers were broken. I was getting a ND before the new pump. I'm also getting a ND after new pump installed. I believe I need a new board but can't find the right one. How exactly do you check the voltage on the pump. There is no restriction on the hoses they were taken off and checked. Plus, I suck the excess water out through them, while I'm trying to figure out whats wrong. Thanks