Kitchenaid Washer KHWV01RSS0 Leaking

Flexible door bellow seal prevents water leaks between drum and door on front-load washers. Replace if torn, moldy, or leaking. Verify fit by model number.

Secures the door bellow seal to prevent leaks. Replace if damaged, rusted, or if the seal won't stay in place. Confirm fit with your model number.

Secures the door boot seal to prevent water leaks in front-load washers. Replace if rusted, corroded, or fallen off. Confirm fit with your model number.

Drain hose for washing machines. Connects tub to pump to carry water during drain cycles. Replace if cracked, leaking, or damaged. Includes anti-siphon ball.

Replacement drain hose for washing machines. Connects the drum to the drain outlet. Replace if cracked, split, leaking, or worn from rubbing against shocks.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Fix water leaking into your washer between washes or continuous filling. This water inlet valve controls hot and cold water flow. Easy DIY repair.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This replacement seal restores a watertight connection in your washer to help prevent leaks and moisture damage. It replaces a worn, cracked, or flattened original seal so components stay tightly sealed during use.

• Creates a compression barrier between mating parts to contain wash water
• Helps stop drips and seepage during fill, wash, or drain
• Can address water leaks, moisture under the unit, or musty odors from trapped water
• Replaces seals that are brittle, torn, or misshapen

• Disconnect power and turn off water supply before servicing
• Access the seal location per your model's service information and note orientation
• Clean grooves and mating surfaces; seat the new seal evenly (a light film of water or mild soap can aid installation)
• Reassemble and run a short cycle to check for leaks

The Water Inlet Flow Meter is an OEM part for Whirlpool washing machines. It is responsible for monitoring and regulating the flow of water entering the washing machine during the fill cycle, ensuring the correct amount of water is added for efficient and effective cleaning.

Causes of a faulty Water Inlet Flow Meter include sediment buildup, physical damage, or electrical issues with the meter's sensors or connections.  

Symptoms of a bad Water Inlet Flow Meter include:

• Incorrect water levels in the wash tub
• Washing machine not filling properly with water
• Error codes related to water inlet flow or water level issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Seals the washer tub to cabinet, preventing leaks and reducing noise. Replace if cracked, torn, or leaking. Verify fit with your model number.

Replacement outer tub for front-load washers. Houses the spin basket and seals water inside during wash cycles. Replace if cracked, damaged, or leaking.