Whirlpool Dishwasher GU2475XTVB3 Leaking

Fix dishwasher leaks on the floor with this door gasket and strike kit. Easy 15-minute repair—gasket presses into groove, no glue needed. Video included.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Flexible drain hose carries wastewater from your dishwasher to the kitchen drain. Replace if cracked, leaking, burst, or damaged by wear or pests.

Carries wastewater from your dishwasher to the household drain. Replace if cracked, punctured, or leaking. Installs at pump outlet and drain connection.

Delivers water from supply line to dishwasher tub. Replace if cracked, leaking, chewed by rodents, or damaged during installation or moving.

Dishwasher not filling with water? A faulty water inlet valve is often the cause. This valve controls water flow into your dishwasher. DIY-friendly repair.

The Rubber Washer is an OEM part for Whirlpool dishwashers. This washer plays a role in ensuring a leak-proof seal at various connection points within the dishwasher, such as at the water inlet valve or hose connections. Its primary function is to prevent water from leaking out of the dishwasher during operation, thereby ensuring efficient and safe use of the appliance. 

Over time, rubber washers can deteriorate due to the constant exposure to water and chemicals found in dishwasher detergents. 

Symptoms of a bad Rubber Washer in a dishwasher include:

• Visible signs of wear or damage to the washer, such as cracks, brittleness, or deformation.
• Water leaking from the dishwasher, particularly around areas where hoses and valves connect.
• A decrease in dishwasher performance due to water not being contained properly during cycles.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Fix continuous water flow or dishwasher overflow issues. This inlet valve controls water entering your dishwasher. Easy DIY repair with basic tools.

Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.

12 Ft in length

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing wastewater from the dishwasher tub during the drain cycle, ensuring that the dishwasher operates efficiently and effectively.

Causes of a bad drain pump can include clogging from food particles and debris, damage to the pump impeller, or electrical failures within the pump motor. Over time, regular use can lead to wear and tear that affects the pump's performance.

Symptoms of a bad drain pump include:

• Water not draining from the dishwasher
• Standing water at the bottom of the dishwasher after a cycle
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Creates a watertight seal between the spray arm and water supply tube. Replace if you notice leaking or poor spray performance during wash cycles.

Seals the water inlet connection to prevent leaks where water enters the dishwasher tub. Replace if you notice moisture damage or leaking at the valve inlet.

Dishwasher leaking from bottom or making grinding noise? The sump housing often cracks or wears out. Moderately difficult repair, about 45 minutes.