Whirlpool Dryer Drum, Bulkhead, Front Parts

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

Replacement dryer drum front bulkhead panel. Installs at the front of the drum assembly. Needed when cracked, warped, or damaged from wear.

Front bulkhead panel that supports the dryer drum and seals the cabinet. Replace if cracked, warped, or damaged to restore drum alignment and airflow.

Replaces the front bulkhead section of your dryer drum. Needed when the drum front is cracked, dented, warped, or damaged, affecting tumbling performance.

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

Complete drum assembly for dryers. Houses and rotates laundry during cycles. Replace if cracked, warped, damaged, or worn from extended use.

Replace a cracked, dented, or broken dryer drum front bulkhead. This structural component holds and supports laundry during the drying cycle.

Front bulkhead assembly for your dryer drum. Replaces cracked, warped, or broken bulkheads. Mounts to the front of the drum for structural support.

This replacement dryer drum is the rotating tub that holds and tumbles clothes while channeling airflow for even drying. Swap a damaged drum to stop rubbing noises, fabric snags, and uneven tumbling. What it does:

• Rotates inside the dryer cabinet to tumble laundry and direct hot air through the load.
• Supports the drum belt and rides on rollers/glides for smooth operation.
• Replace when you see dents, cracks, deep gouges, or metal-to-metal contact.
• Common symptoms of a failing drum: scraping or grinding noises, clothes catching, visible drum damage, or uneven tumbling.
• Inspect rollers, glides, and belt when replacing the drum.

• Disconnect power (and turn off gas supply for gas dryers) before beginning any repairs.
• Support the drum when removing or installing to avoid dropping or damaging the cabinet or finish.
• Installation typically requires removing the dryer front or top panels and repositioning the belt and rollers; have basic hand tools ready.
• If you hear persistent noises after install, recheck belt alignment, roller condition, and cabinet mounting.

Front bulkhead drum assembly for your dryer. Installs as the front section of the rotating drum. Replace if cracked, damaged, or worn from regular use.

Replaces a cracked, dented, or damaged dryer drum bulkhead. This front drum component restores smooth tumbling action when the original is worn or broken.

Front bulkhead for dryer drum assembly. Replaces cracked, broken, or damaged bulkhead components. Essential structural part for proper drum support.

Front bulkhead for your dryer drum assembly. Replace this structural component if it's cracked, damaged, or worn to restore proper drum support.

This bulkhead is the structural panel that supports and seals the washer tub and provides mounting points for related components. It restores proper alignment and containment so the washer can hold and drain water correctly. What it does:

• Provides a secure mounting surface for the tub, seals, and associated fittings
• Helps route and contain water inside the washer cabinet to prevent leaks
• Maintains correct alignment for the tub and connected components
• Commonly replaced when leaks, cracks, or warped mounting surfaces cause water loss or misalignment

• One bulkhead panel

• Turn off power and water supply before beginning any repair
• Handle gently to avoid damaging mating surfaces or embedded seals
• Verify matching orientation and fastener locations to the original part
• If seals or gaskets are attached separately on your model, replace them as needed

Replacement drum front bulkhead for dryers. Installs at the front of the drum assembly. Needed when original is cracked, damaged, or worn out.