Parts for Maytag MLG2000AWW: 03 - Cabinet-Front (Washer) Parts

Specs: No.8X1/2 HEX WASHER HEAD

Specs: 10 - 16 x .375

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

Fixes washer overfilling or not filling correctly. This pressure switch senses water level to control fill cycles. Easy 15-minute repair.

Secures the washer cabinet to the frame to control movement and vibration. Replace when fatigued, broken, or worn through to restore stability.

Color: White

Color: White This part has been discontinued and is no longer available.

Retaining clip secures the front panel to the cabinet sides on washers and washer-dryer combos. Replace when clip is broken, missing, or won't hold panel.

This spring support secures a suspension spring to the washer's frame, helping keep the tub stable during wash and spin. Replacing a damaged support restores proper balance control to reduce vibration and banging. What it does:

• Anchors a suspension/tub spring to the cabinet or base
• Helps control tub movement and maintain alignment during spin
• Failure can cause excessive vibration, banging, off-balance shutdowns, or a leaning tub
• Visible cracks, bent tabs, or a detached spring indicate the support needs replacement

• 1 spring support

• Disconnect power and turn off water before servicing
• Support the tub and carefully relieve spring tension before removing the old support
• Transfer the spring to the new support and install in the original location/orientation
• Wear gloves and eye protection; springs are under tension

Spesc: #12 pozi - drive

Specs: 10 - 16 x .375

Specs: 10 - 16 x .375

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

Replace your washer's bleach dispenser cup screen when clogged or damaged to ensure proper bleach flow. Confirm fit with your model number before ordering.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

A small replacement clip that secures the dispenser hose to the dispenser assembly, helping keep the hose seated and reducing the chance of leaks or disconnection. Simple, durable part for restoring proper hose retention. What it does:

• Holds the dispenser/hose connection firmly in place to prevent the hose from slipping free
• Helps reduce water leaks and intermittent dispenser flow caused by a loose hose
• Keeps hose routing stable to avoid rubbing or wear against nearby components
• Works with the dispenser assembly to maintain proper alignment and seal

• One retainer as shown

• Disconnect power and water supply before starting any repair
• Access the dispenser area per your appliance's service instructions; remove trim or panels if required
• Snap the retainer over the hose at the dispenser connection until it seats; verify the hose is fully seated
• If you see damage to the hose or fittings, replace those parts before finishing

Replace your washer's bleach dispenser hose if you notice leaks, cracks, or bleach not dispensing properly. Verify fit with your model number listed.