Parts for Maytag A101: 05 - Motor Mount, Base Frame & Center Spring Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This genuine OEM part is a washer motor. The washer motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. After continuous use, a washer motor can become inoperable. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the motor needs to be replaced. To replace the motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting bolts holding it to the washer. Proceed to pull the old motor out of its place. Make sure to detach the wire harness and any individual wires on the motor. Reinsert the wires into their correct terminals and install the new motor by threading the bolts that secure it. This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand washers.

This factory spring kit restores the designed tension and return action in the affected assembly so moving parts operate smoothly, stay in position, and wear evenly over time.

• Provides the correct counterforce to position or balance components
• Maintains steady tension to prevent drift, slamming, or misalignment
• Helps reduce squeaks, chatter, or uneven movement from fatigued springs
• Typical signs of failure: weak return, inconsistent movement, excess noise, or visible spring damage

• Disconnect power; shut off water or gas before servicing
• Wear eye protection—springs are under tension
• Note original spring anchor points and replace all springs in the kit as a set
• Use appropriate pliers or a hook tool; verify smooth operation before reassembly

Screw: 8-16 x 3/8 inch.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This part has been discontinued by the manufacturer and is no longer available.

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

Washer won't spin or spins slowly? This motor mount roller and spring kit restores proper spin performance. Moderately easy DIY repair with video guide.

This part has been discontinued by the manufacturer and is no longer available.

Size: 10-32

2 ounce bottle

The High-Temperature Adhesive Tube is an OEM part for Whirlpool appliances. This adhesive is specifically formulated to withstand extreme temperatures, making it ideal for securing components in ovens, dryers, and other high-heat environments. It is commonly used to seal or repair gaskets, felt seals, and other parts that require a durable bond to maintain integrity under thermal stress.

Symptoms of a need for High-Temperature Adhesive include:

• Loose components or seals within high-heat appliances
• Heat escaping from appliance seals
• Unusual noises due to parts shifting that are normally secured

Causes for the use of high-temperature adhesive can stem from normal wear and tear that loosens components or degradation of previous adhesive applications due to prolonged exposure to high temperatures.

This product is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specialty lubricant for washer transmission center seals. Replace when servicing seals or bearings to ensure smooth operation. Confirm fit by model.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.