Parts for Maytag WU201: 07 - Front View-Panels Removed (Ser. 01 & 02) Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.

Screw: 8-16 x 3/8 inch.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

A replacement mounting screw used to secure appliance panels and components. This genuine-style fastener restores proper fit and prevents loose or rattling parts for many Whirlpool appliances. What it does:

• Fastens panels, trim, brackets, or components to the appliance frame
• Restores secure attachment when original screw is missing, stripped, or damaged
• Helps eliminate rattling, vibration noise, and loose-fitting parts
• Matches OEM fit and function when the correct part number is used

• Disconnect power (and water, if applicable) before servicing the appliance.
• Use the correct screwdriver or driver bit to avoid stripping the head; do not overtighten.
• Replace only with the exact part number to ensure correct fit; keep removed hardware organized for reassembly.

Specs: 10 - 16 x .375

Size: 10-32

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

This part has been discontinued by the manufacturer and is no longer available.

For belt driven models

Replace your dishwasher's worn or missing washer. Installs on spray arm pipe or door components. Needed when old washer is cracked or damaged.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This drive belt links the dishwasher's motor to the pump so the machine can circulate wash water and drain properly. Replacing a worn or broken belt restores wash action and helps eliminate slipping or squealing during cycles.

• Transfers motor power to the pump for water circulation and draining
• Common fix for no wash action or poor cleaning
• Can address squealing/chirping noises or a burning rubber smell
• Replaces belts that are cracked, frayed, stretched, or glazed

• Disconnect power and turn off the water supply before servicing
• Remove the lower access/toe panel to reach the motor and pump area
• Note belt routing; rotate the old belt off the pulleys and install the new belt the same way
• Check pulley alignment and hand-rotate to seat the belt before running a test cycle

This part has been discontinued by the manufacturer and is no longer available.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.