Parts for Maytag SDG3606AWW: 07 - Rear Bulkhead Parts

Connects the motor to the drum for tumbling. Replace when stretched, worn, or broken causing the drum not to turn. Confirm fit with your model number.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

Fix a dryer that hums but won't turn with a new drive motor. This repair addresses seized bearings and worn motor assemblies. Moderate DIY project.

Fix no airflow or squealing dryer with this blower wheel replacement. Restores proper air circulation through drum and exhaust. Moderate DIY repair.

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

Fix a dryer that overheats, won't dry completely, or stops mid-cycle. This cycling thermostat regulates heat to prevent damage. DIY-friendly repair.

This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.

• Controls the heating circuit to maintain target drying temperatures
• Provides temperature feedback for accurate auto-dry operation
• Common symptoms: long dry times, very hot drum/cabinet or scorching odors, auto-dry not advancing correctly, or no heat if the thermostat fails open
• Typically mounted on the blower housing to sense exhaust air temperature

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat (commonly on the blower housing); remove the necessary panel(s)
• Transfer wires one at a time to the new thermostat and mount it flat against the housing
• Reassemble, verify clear venting/airflow, and run a test cycle

The Spring Idler is an OEM replacement part for Speed Queen residential clothes dryers. It works with the dryer drum to facilitate the controlled tumbling of laundry items during the drying cycle. Proper functioning is important for efficiency and effectiveness.

Causes of a bad spring idler can include material fatigue from years of repetitive use. It can also result from overloading the dryer with excessively heavy wet loads that put abnormal stress on the idler mechanism.

Symptoms of a failed spring idler include:

• The dryer drum not rotating smoothly
• Clothing failing to tumble freely and wrinkling instead
• Prolonged drying cycles and increased energy use
• Noisy squeaking or creaking emanating from inside the dryer

As the mechanism responsible for facilitating optimal tumbling, this OEM Speed Queen replacement idler spring restores smooth and efficient dryer operation.

This dryer idler arm pivots from the motor mount bracket to maintain belt tension. Replace if cracked, worn, or binding to restore smooth operation.

The Thrust Washer is an OEM part for Whirlpool washers and dryers, reduces friction between moving parts within the appliance. This small component is placed between rotating surfaces to ensure smooth operation and to extend the lifespan of those parts. The thrust washer can wear down or become damaged due to the constant pressure and movement.

Causes for replacement may include normal wear and tear, overloading the appliance, which puts extra stress on mechanical components, or a lack of regular maintenance.  

Symptoms of a bad Thrust Washer include:

• Increased noise during operation
• The appliance vibrating more than usual
• A decrease in performance efficiency

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Maintains belt alignment and tension in your dryer. Replace if pulley is squeaking, seized, cracked, or no longer spinning freely on the shaft.

The Retaining Ring is an OEM replacement part for Whirlpool dryers and washing machines. This retaining ring holds the rear wheels on the axels of the washer or dryer. 

Symptoms of a bad retaining ring can include wear and tear over time, damage due to accident or impact, or corrosion affecting the structural integrity.

Causes of a bad retaining ring dryer include:

• Excessive vibration or movement of the drum during operation 
• Noise or banging sounds from loose components   
• Deformation or cracking of the retaining ring itself
• The dryer door not closing properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix loose or rattling parts with this 1/4-20 nut. Secures components in dryers, washers, and microwaves. Quick 5-minute repair restores stability.