Parts for Bosch SGV45E03UC/01: Base Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

If your dishwasher won't fill with water or makes thumping noises, the water inlet valve likely needs replacement. Moderate DIY repair from base.

Replaces cracked, kinked, or leaking dishwasher drain hose. Connects unit to household drainage system. Essential when hose is damaged or worn.

Drain hose clamp

2 clamps included.

Replace a cracked or damaged dishwasher bottom case. This structural component forms the lower housing of your dishwasher, protecting internal parts.

Front leveling leg adjusts and supports your dishwasher at the front. Replace if damaged, missing, or worn to restore proper height and stability.

Replacement tank mounting bushing for your dishwasher. Secures the wash tank assembly in place. Order a new bushing if yours is cracked or missing.

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Dishwasher overfilling or won't stop filling? This float switch lever activates the water level sensor. Simple DIY fix restores proper fill control.

Replacement shaft that secures and guides the dishwasher float for accurate water level detection. Needed when the original shaft is worn or broken.

Protective cover panel for the bottom front of your dishwasher. Replaces cracked, bent, missing, or discolored kickplates to restore appearance.

Protective cover panel for the bottom front of your dishwasher. Replaces cracked, bent, missing, or discolored kickplates to restore appearance.

Cotton sound-dampening pad installs under the dishwasher tub base. Replace if worn, torn, missing, or compressed to restore noise reduction.

Replacement adjuster socket for dishwasher leveling feet. Installs at cabinet base to raise or lower the unit for level installation. Replace if cracked or stripped.

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

The Roller and Cable Assembly is an OEM part for Bosch dishwashers. This assembly includes the roller and cable, which work together to facilitate the smooth operation of the dishwasher door, allowing it to open and close effortlessly.

Over time, the roller and cable can wear out or become damaged due to regular use, friction, or accidental mishandling. If either component fails, it can affect the balance and movement of the dishwasher door, making it difficult to operate.

Symptoms of a bad roller and cable assembly include:

• Difficulty in opening or closing the dishwasher door
• A sagging or misaligned door
• Unusual noises when operating the door
• The door not staying securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Plastic bushing that guides and supports the dishwasher door hinge assembly. Replace if cracked, broken, or worn causing noisy or misaligned door movement.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Left side door hinge for your dishwasher. Replaces damaged, bent, or broken hinges that cause the door to fall open or swing too far. Bushing included.

Left-hand hinge lever for dishwasher doors. Assists door opening and closing through pivoting motion. Replace if cracked, broken, or damaged from overextension.

Plastic bushing that guides and supports the dishwasher door hinge assembly. Replace if cracked, broken, or worn causing noisy or misaligned door movement.

Left hinge cap for dishwasher door assembly. Replaces cracked, broken, or missing hinge caps. Cosmetic and structural part for door hinge cover.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Roller and Cable Assembly is an OEM part for Bosch dishwashers. This assembly includes the roller and cable, which work together to facilitate the smooth operation of the dishwasher door, allowing it to open and close effortlessly.

Over time, the roller and cable can wear out or become damaged due to regular use, friction, or accidental mishandling. If either component fails, it can affect the balance and movement of the dishwasher door, making it difficult to operate.

Symptoms of a bad roller and cable assembly include:

• Difficulty in opening or closing the dishwasher door
• A sagging or misaligned door
• Unusual noises when operating the door
• The door not staying securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Plastic bushing that guides and supports the dishwasher door hinge assembly. Replace if cracked, broken, or worn causing noisy or misaligned door movement.

Right side door hinge for dishwashers. Installs on the right side of the door frame. Replace if bent, broken, or damaged from door falling too hard.

The Hinge Lever (RH) is an OEM component specifically designed for Bosch dishwashers. This right-hand lever is a part of the dishwasher door hinge assembly, working to open and close the door during each use. 

Causes of a bad hinge lever can include wear and fatigue over thousands of opening and closing cycles. Damage can also potentially occur from any impact or denting of the door surface near the lever mechanism.

Symptoms of an ineffective hinge lever include:

• The dishwasher door sagging or becoming misaligned  
• Difficulty fully opening or closing the door
• Loud squeaks or grinding noises coming from the hinges
• The door potentially detach from the hinge if broken 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.

Plastic bushing that guides and supports the dishwasher door hinge assembly. Replace if cracked, broken, or worn causing noisy or misaligned door movement.

Replace your dishwasher's broken or missing right hinge cap. This cover installs on the door hinge to provide a finished look and protection.

Dishwasher door guard installs on the door hinge for reinforcement and support. Replace if cracked, broken, or missing to prevent door bending.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Dishwasher won't start or keeps tripping the breaker? A damaged terminal box with melted connections is often the cause. Moderate DIY repair.

Replace a missing or damaged junction box cover on your dishwasher. Protects power supply and control board wiring connections. Easy DIY repair.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

The 4 x 16 Screw is an OEM component for Bosch dishwashers. 

Common causes of faulty screws include standard wear from years of housing vibrations during wash cycles. Mineral deposits lingering around screw heads also risk eventual corrosion and seizing issues.

Symptoms of potentially loose or damaged screws comprise:

• Odd knocking or buzzing noises from inside cabinets
• Detached or misaligned door panels 
• Water leaks developing between internal seams
• Components unable to be fully secured down during repairs

This screw type is additionally suited for Thermador, Gaggenau as well as some premium Kenmore dishwashers.

The Toe Panel Screw is an OEM replacement part for Bosch dishwashers. It secures the toe panel to the dishwasher.

Causes may involve normal wear and tear over time, improper installation, or damage from excessive force or impact. Replacing with this genuine OEM screw will reinforce your Bosch dishwasher's integrity for reliable performance.

Symptoms of a bad toe panel screw can include:

• The toe panel becoming loose, cracked, or removable
• Internal components visible underneath a loose toe panel
• Strange noises or vibration emanating from the toe panel area

This OEM Bosch part is also compatible with Thermador, Gaggenau and some Kenmore models.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.