Parts for Kitchenaid KSM90PSGR0: 04 - Base And Pedestal Unit, Optional Parts

The Cap-Screw is an OEM component specifically designed for Whirlpool mixers. It contains precision mixing mechanisms that allow users to easily and effectively blend, whip, or beat ingredients.

Symptoms of a bad Cap-Screw include:

• Difficulty turning on or selecting speeds
• Excessive noise or vibration during use
• Inconsistent mixing performance
• Leaks into electrical components

Causes of failure can be faulty power switches, worn gears, damaged housing or bowls, or deterioration of internal wiring over time.

This Cap-Screw is also compatible for use with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore.

This lever latch is the replacement latch used to secure and release the appliance door or access panel, restoring proper door engagement and user operation. It fits the OEM latch location and matches the original white/storm-gray finish. What it does:

• Replaces a broken, cracked or worn latch lever that prevents the door from closing or latching securely
• Restores smooth open-and-close action for the affected door or panel
• Prevents rattling or misalignment caused by a damaged latch
• Matches the original finish to maintain the appliance appearance

• One lever latch (white/storm-gray), as shown

• Disconnect power to the appliance before beginning any repair
• Remove the damaged latch and install the replacement using the factory mounting points; fasteners or clips may be required depending on model
• Handle small plastic parts carefully to avoid breakage during installation
• Refer to your model-specific parts diagram or service manual for exact removal and reassembly steps

Replaces a cracked, broken, or missing control knob on your stand mixer's speed or lock lever. Restores comfortable grip and clean appearance.

Rubber foot for stand mixers. Installs at the base to provide stability. Replace if worn, cracked, missing, or damaged to prevent mixer movement.

Replacement hinge pin for stand mixer tilt heads. Secures the pivoting head assembly. Install if your original pin is missing, sliding out, or worn.

This latch, link, and lever assembly restores proper latching action so the door or lid closes securely and the appliance can run as intended. It replaces worn or broken linkage that can prevent the latch from engaging.

• Connects the latch to its operating lever to enable smooth open/close action
• Helps resolve issues like a door/lid that won't latch, pops open, or won't start due to an unlatched condition
• Prevents intermittent cycle interruptions caused by a weak or misaligned latch linkage
• Durable components designed to maintain consistent latch engagement

• Unplug or disconnect power before servicing
• Access the latch area per your model's service information
• Note linkage orientation during removal to ensure correct reassembly
• Test latch engagement and operation before returning to service

This latch secures the appliance door and helps ensure a proper close for normal operation. It replaces a worn or broken latch to restore reliable door engagement and user safety. What it does:

• Holds the door closed so the appliance can operate as intended
• Replaces a damaged or broken latch that prevents the door from staying shut
• Helps restore proper alignment and engagement of the door mechanism
• Can reduce door rattling or intermittent closing issues

• Latch

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the door or access panel to reach the latch per your model's service instructions
• Compare the new latch to the old part for correct orientation before installation
• Test the door operation after installation to ensure secure engagement

Washer for stand mixers. Installs between components to provide cushioning and proper spacing. Replace if worn, cracked, or missing for secure fit.

Secures hinge, lever, or linkage to its bracket on your stand mixer. Replace this screw if stripped, missing, or damaged to restore proper alignment.

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Replacement mounting screw for stand mixers. Secures panels, brackets, and internal components. Needed when original is missing, stripped, or damaged.

Flat beater attachment for stand mixers. Mixes and blends ingredients in the bowl. Replace if coating is worn, peeling, cracked, or damaged.

Replace your cracked, worn, or missing 4.5-quart stainless steel mixing bowl. Fits tilt-head stand mixers with handle for easy pouring and removal.

Dough hook attachment for KitchenAid stand mixers. Kneads bread, pizza, and roll dough. Replace if your original hook is lost, damaged, or missing.

Wire whip attachment for stand mixers incorporates air into ingredients for whipping cream, egg whites, and fluffy mixtures. Replace if bent or corroded.

Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.

Stand mixer Rotor Slicer, Shredder Attachment for KitchenAid Stand Mixer that includes four stainless steel slicing, shredding cones, and instruction booklet. The slicers include course, thick, think and fine shredder to shred vegetables, fruit and nuts. KitchenAid model number RVS-A

This speed disc is a service replacement used with the washer's speed/transmission assembly to restore correct drive engagement during repairs. It provides a direct, OEM-style replacement for technicians performing maintenance or part swaps. What it does:

• Replaces the washer's service speed disc used in the transmission/drive assembly
• Helps restore proper drive engagement and consistent agitation or spin behavior
• Used during service or repair to address slow or inconsistent spinning and agitation symptoms
• Matches OEM fit and form for affected drive components

• Disconnect power and water supply before beginning any repair
• This part installs inside the transmission/drive area and typically requires removing the washer cabinet and access panels
• Handle carefully to avoid bending or contaminating mating surfaces; confirm orientation before final assembly

Two pack Lid Covers used with 4.5 and 5 Quart KitchenAid Tilt Head Stand Mixer. The covers are used for variety of situations for example, when you need to keep ingredients in the bowl cold for hours or want to save extra cookie dough. The Lid Covers are dishwasher safe on the top-rack and fit KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB.

Replace your cracked, worn, or missing 4.5-quart stainless steel mixing bowl. Fits tilt-head stand mixers with handle for easy pouring and removal.

Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.

Lubricates planetary gears in stand mixers. Replace when grease darkens, mixer makes noise, or after gear replacement. Confirm fit with your model.