Parts for Ge GHDS830ED1WS: Blower & Motor Parts

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Secures the ground wire to the dryer cabinet for safe electrical connection. Replace if missing, stripped, or corroded to restore proper grounding.

This blower wheel is the replacement fan wheel that moves air through the dryer to support efficient drying and proper venting. Restores airflow from the dryer drum to the exhaust system for more consistent drying performance. What it does:

• Spins on the motor shaft to draw air over the heating element and through the drum.
• Restores proper airflow to reduce long dry times and improve drying consistency.
• Replaces damaged or unbalanced wheels that cause vibration, wobble, or unusual noise.
• Helps prevent overheating by maintaining proper venting when working with a clean vent system.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the dryer front or rear access panel and the drive belt or motor mounting hardware; follow the model service manual.
• Inspect the motor shaft and blower housing for wear, lint buildup, or obstructions and clean the vent system while replacing the wheel.
• Replace or repair worn motor bearing or shaft components to prevent repeat failures.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

This idler arm assembly keeps the dryer belt properly tensioned so the drum turns smoothly for effective drying. It replaces worn or damaged tensioners to restore normal drum rotation and reduce noise. What it does:

• Maintains correct belt tension so the drum can rotate during operation
• Guides the dryer belt to prevent slipping or off-tracking
• Reduces squealing or grinding caused by a worn idler pulley
• Helps prevent premature belt wear and drum stoppage

What's included:

• One idler arm assembly with pulley

Install notes:

• Disconnect power to the appliance before beginning any repairs
• Relieve belt tension carefully; some designs include a spring—handle with caution
• Basic hand tools required; check belt routing and alignment during reassembly

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

This idler arm bracket secures the dryer idler pulley assembly to maintain proper belt alignment and tension so the drum turns smoothly. It's a direct-fit replacement that helps stop belt slipping and uneven drum movement. What it does:

• Holds the idler pulley assembly in the correct position to route and tension the drive belt
• Restores consistent belt tension to prevent slipping and premature wear
• Helps eliminate symptoms like squealing, grinding, or a drum that hesitates or won't turn smoothly
• Works with the existing idler pulley and belt to ensure reliable drum rotation

• Disconnect power (and gas supply for gas models) before starting any repair
• Access the bracket by removing the dryer front or lower access panel per your model's service instructions
• Relieve belt tension, remove the old bracket, and install the replacement using the original fasteners; inspect the pulley and belt for wear while you're inside

If your dryer drum won't turn or spin, this motor and pulley assembly powers drum rotation for normal drying. Direct replacement drive motor unit.

If your dryer fan won't run or runs intermittently, the blower wiring harness may have failed. This assembly restores electrical connections to the fan motor.

This small mounting screw secures panels and trim on compatible GE appliances, restoring a solid, vibration-free fit. Use it to replace a missing, stripped, or damaged fastener and keep parts aligned and secure. What it does:

• Fastens panels, trim, or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Restores secure attachment when threads are stripped or worn
• Helps maintain proper alignment to prevent noise and component wear

• Use the correct screwdriver size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power or move the appliance to a safe position when accessing internal panels
• Consider a replacement clip or insert as recommended by the manufacturer