Parts for Ge ZGP304LR2SS: 04 - Body Parts

Stainless steel cleaner for gas ranges and cooktops. Restores shine and removes fingerprints, smudges, and streaks from exterior surfaces.

Gas orifice assembly for range burners. Regulates gas flow to burner heads. Replace if orifice is clogged, damaged, or missing for proper burner operation.

Lubricant cleaner for range and oven control shafts, burner valves, and rack paddles. Dissolves residue and restores smooth operation when parts feel stiff.

This bake supply tube assembly routes gas to the oven's bake burner so the oven can produce heat for baking. It replaces a damaged or leaking tube to restore proper burner operation and safe performance. What it does:

• Delivers gas from the manifold to the oven's bake burner for ignition and steady flame
• Restores normal baking heat when the supply tube is cracked, clogged, or disconnected
• Helps eliminate weak or no-bake heat caused by interrupted gas flow
• Designed to align with the oven's burner and sealing surfaces for proper combustion

• For gas appliances: turn off gas supply and electricity before servicing; follow manufacturer instructions
• Install only when cool; inspect and replace any damaged gaskets or fittings
• Use proper fittings and tighten to OEM torque; check all connections for leaks after installation with an approved method

This wire bushing protects appliance wiring where wires pass through metal or plastic panels, helping prevent chafing and shorts. It restores a safe insulating barrier to wiring harnesses and terminals. What it does:

• Cushions and isolates wires where they pass through openings to prevent abrasion and wire damage
• Helps stop rubbing that can wear insulation and cause arcing or shorts
• Reduces risk of intermittent power, blown fuses, or burning smells from damaged wiring
• Restores proper routing and strain relief for affected harnesses

• Remove power to the appliance before accessing wiring; disconnect power at the breaker or unplug.
• Inspect surrounding wire insulation and harness for damage; replace any wires that show charring or exposed conductors.
• Push the bushing into the opening until seated, then route the wire through the bushing to ensure a snug fit.

Range display lights flickering or completely dark? This LED power supply module converts voltage to power your control panel lighting. Moderate DIY repair.

Range not heating or igniting? This control relay board routes power to igniters and burners. Fixes intermittent operation and failed starts on gas ranges.

This door seal gasket maintains your range's internal temperature and prevents moisture buildup. Replace when worn or damaged to restore efficient closure.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Size: 8-18 x 1/2 inch.

Secures the toe kick panel to your range base. Replace if the toe kick is loose, rattling, or won't stay in place. Verify fit with your model number.

Leveling leg kit for ranges and wall ovens. Includes adjustable feet to stabilize and level your appliance. Replace cracked, bent, or missing legs.

Secures freestanding ranges to the floor or wall to prevent tipping. Replace if bracket is missing, bent, or damaged during appliance installation.

Secures your range to the floor or wall to prevent tipping when the oven door is open. Replace if bracket is bent, broken, or missing during installation.

Fix uneven oven temperatures or overheating electronics with this 45mm tangential blower motor. Restores directed airflow in your gas range cavity.

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

This access back panel covers the rear of the appliance to protect internal components and restore a finished appearance. It provides a secure mounting surface and keeps wiring and parts enclosed for safe operation. What it does:

• Covers and protects internal wiring, controls and components at the appliance rear
• Restores a finished exterior and helps prevent dust and debris entry
• Secures with factory mounting points to stop rattling or loose panels
• Replaces missing, bent, or corroded rear access panels that expose internal parts

• Disconnect power and pull the appliance away from the wall before installing.
• Use correct screws and hardware for secure mounting; verify alignment with factory holes.
• Handle edges carefully; wear gloves to avoid cuts.

This small metal nipple secures or connects appliance components, restoring proper alignment and a stable mechanical or fluid connection. It's a simple replacement that helps appliances function reliably. What it does:

• Provides a secure mounting point or connection between parts
• Restores proper alignment for linked components
• Replaces worn or damaged fittings that can cause rattling or instability
• Helps maintain a leak-free or stable mechanical joint when used as intended

• Disconnect power and/or gas and follow all safety procedures before starting work
• Install in the original orientation; hand-start fasteners to avoid cross-threading, then tighten to secure
• If the nipple interfaces with a fluid or gas line, inspect seals and replace gaskets or O-rings as needed and check for leaks after reassembly

Controls gas flow to your range oven burner. Replace this regulator if it's cracked, corroded, or leaking to restore proper gas pressure control.

Positions your range handle at the correct distance from the door. Replace if worn, missing, or cracked to restore proper alignment and prevent rattling.

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement power cord for gas ranges. Installs at the rear connection to supply mains electricity. Order when your original cord is frayed, cut, damaged, or worn.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Mounting bracket that secures the capacitor to your range frame. Replace if bent, broken, or missing to properly support and position the capacitor.

Replacement screw for refrigerators. Secures handles, panels, and internal components. Order if yours is missing, stripped, or lost during repairs.

Fix burners that won't ignite or turn off when your gas range control knobs aren't responding. This reed switch board detects knob positions.