Parts for Hot Point RGA724EK2WH: 03 - Body Parts

Replacement power cord for gas ranges. Connects your unit to the wall outlet. Replace if cord is worn, cut, heat-damaged, or causing burning smells.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Secures your range power cord at cabinet entry to prevent wire damage and disconnection. Replace if cord is loose or clamp is cracked. Confirm fit with your model number.

Replace your range's damaged or missing side panel. This exterior trim piece installs along the side of your oven to restore its finished appearance.

This oven floor deflector assembly restores proper airflow and heat protection in the lower oven cavity so food cooks evenly and internal components stay shielded from direct heat. It's a direct replacement for a damaged or warped deflector. What it does:

• Redirects and evens oven heat across the lower cavity to improve baking and roasting consistency.
• Shields internal insulation and components from hot bake/broil flames and debris.
• Replaces warped, dented, or missing deflector that can cause uneven cooking or rattling.
• Helps prevent direct flame contact with oven floor and lowers risk of food drippings burning on surfaces.

• One bottom oven and deflector assembly

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Basic hand tools are typically required; follow the appliance service manual for panel removal steps.
• Handle edges carefully—metal parts may be sharp.

Size: 8-18 x 1/2 inch.

Includes 12 speed nuts.

Secures the thermostat sensing bulb to the oven cavity wall for accurate temperature control. Replace if missing or damaged to prevent sagging bulb.

Oven door hinge assembly for ranges. Mounts to the oven frame to support and pivot the door. Replace if hinge is broken, bent, or worn causing misalignment.

Anti-tip bracket kit installs to the floor behind your range or wall oven to prevent tipping. Replace if missing, damaged, or moving to a new home.

Base support kit for gas ranges. Installs at the bottom of the range to provide structural stability. Replace if cracked, broken, or missing.

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

Oven insulation wrap installs around the range oven cavity to reduce heat loss and dampen sound. Replace if torn, compressed, or missing for efficiency.

Insulation wrap that fits around the oven cavity to reduce heat loss and dampen sound. Replace if torn, compressed, missing, or damaged during repairs.

Wire clip secures electrical connections to heating elements in ranges. Replace if worn, cracked, or loose to restore proper contact. Verify fit with model.

This hinge deflector guides and protects the refrigerator door at the top hinge, helping the door open and close smoothly and preventing rubbing or catching. It restores correct door alignment and reduces wear on hinge components. What it does:

• Guides the door on the top hinge to maintain proper movement and alignment
• Helps prevent the door from rubbing, scraping, or catching on the cabinet
• Reduces wear and noise at the hinge area caused by misalignment
• Supports smooth opening and closing for a secure seal

• One hinge deflector

• Always unplug the appliance or switch off power before starting work
• Support the door before removing or loosening the top hinge to prevent injury or damage
• Remove the top hinge hardware, replace the deflector, then reassemble and tighten hardware securely
• Check door alignment and operation after installation; adjust hinge hardware as needed

Screw for electric and gas ranges. Secures internal components and panels. Replace if lost, stripped, or corroded to properly fasten range parts.

Insulation that wraps around the safety valve on gas ranges. Replace if torn, deteriorated, or missing to maintain proper heat protection.