Parts for Frigidaire LCE732LW2: 02 - Cabinet And Component Parts

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Top panel for laundry center units. Covers and protects the upper surface. Replace if cracked, chipped, discolored, or damaged from wear and tear.

Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.

For a complete drum bearing and shaft kit order 5303281153.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

Front drum bulkhead for dryers. Mounts inside cabinet to support rotating drum. Replace if cracked, worn, or damaged to restore proper drum rotation.

Bearing support seal for washer dryer combos. Replace if you notice water leaks, unusual noise, or drum wobbling. Verify fit with your model number.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

A single replacement screw fastener used to secure trim, panels, or internal components. Fits specific Frigidaire appliance locations to restore proper fastening and alignment where factory hardware is missing or damaged. What it does:

• Secures plastic trim, brackets, or metal panels in refrigerators and freezers
• Restores proper alignment and prevents rattling or loose parts
• Replaces stripped, corroded, or lost hardware to maintain appliance function
• Works wherever the original factory screw was specified

• One replacement screw

• Use the correct screwdriver or bit to avoid damaging the screw head
• Do not overtighten; snug until seated to prevent cracking plastic or stripping threads
• Replace only with the exact factory part for proper fit and function
• Unplug the appliance or turn off power first if working near electrical components

Dryer drum shaft that supports the drum and connects to the bearing. Replace if worn, damaged, or causing squeaking noises. Verify fit with your model.

Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This mechanical temperature control thermostat regulates refrigerator temperature to keep food cold and cycling the compressor as needed. Replaces a faulty control to restore proper cooling performance and temperature stability. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to maintain set temperature.
• Stops the compressor when the refrigerator reaches the selected temperature and restarts it as needed.
• Commonly replaced when the fridge runs continuously, won't reach set temperature, or has erratic cooling cycles.
• May produce a clicking sound when switching or fail to make electrical contact, causing cooling loss.

• Disconnect power to the appliance before starting any repair.
• Access may require removing interior panels or control housing; keep track of fasteners and wire locations.
• Verify wiring and operation with a multimeter; replace only with the correct OEM part.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This part has been discontinued and is no longer available

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.