Parts for Ge WPRB9220DCCC: 02 - Cabinet, Cover & Front Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.

Bushing that supports the washer lid hinge mechanism. Replace if cracked, worn, or causing the lid to sag or close improperly. Direct fit part.

Rubber bushing that cushions and protects wires from sharp edges inside your washer. Replace if cracked, worn, or missing to prevent wire damage.

Replaces a short wireform hinge that secures your washer lid or access panel. Order a new hinge if yours is rusted, bent, cracked, or missing.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor that helps regulate current to heating and motor circuits, restoring proper cycling and output in affected appliances. What it does:

• Controls and switches power to heating elements or motors by gating current flow
• Helps the appliance regulate temperature or motor speed when functioning correctly
• A failing SCR can cause no heat, intermittent heating, or erratic motor behavior
• Designed to mount to a flange with a .625-inch tab for electrical connection

• Always disconnect power at the breaker or unplug the appliance before servicing
• Handle the SCR by its edges; avoid touching terminals and observe ESD precautions when possible
• Verify proper orientation and secure mounting to the heatsink or chassis per the service manual

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Sound dampening insulation pack for washers. Installs inside cabinet to reduce noise and vibration. Replace if torn, compressed, or missing pieces.

Size: 8 - 18 ab.

Replaces broken or worn tub dampening straps that stabilize your washer's inner tub during operation. Restores proper suspension to reduce vibration.

Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.

Grounding clip for top-load washers ensures proper electrical grounding. Replace if damaged, corroded, or missing to maintain safe operation. Verify fit with your washer model number before ordering.

Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.

Hex washer head screw for washer pedestals. Secures pedestal components and panels. Replace if screw is stripped, missing, or damaged during assembly.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.

6-20 x 3/8 in. screw secures panels and brackets inside washers. Replaces missing, stripped, or damaged fasteners to restore proper fit and stability.

Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.

Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.

Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.

Replaces worn or damaged washer sound dampening isolator. Reduces vibration and noise during wash cycles. Essential when original is cracked or missing.

Fix a washer lid that won't lock or cycles during wash with this lid lock assembly. Common repair for washers that won't start or stop mid-cycle.

A foam insulation barrier that helps seal and protect refrigerator cabinet cavities from air and moisture intrusion. Replaces worn or damaged foam to support proper airflow and reduce the risk of frost buildup around internal components. What it does:

• Provides an insulating seal between cabinet panels and service openings
• Helps limit warm air ingress that can cause frost or reduced cooling performance
• Cushions and isolates components to reduce vibration noise
• Restores original fit where foam has deteriorated or been removed during repairs

• Disconnect power to the appliance before starting any repair
• Remove surrounding panels as needed to access the foam location
• Clean and dry mounting surfaces before applying; use adhesive if required by OEM instructions
• Avoid compressing or blocking vents and airflow paths during installation

Size: 10-12 a. Includes 12 screws.

Base assembly for washers. Installs at the bottom of the cabinet to support the machine. Replace if cracked, damaged, or structurally compromised.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Size: 8-32 t. Includes 12 screws.

Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.

Replacement drain hose for top-load washers. Connects washer to household drainage system. Replace if cracked, leaking, crushed, or missing.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.

Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.