Parts for Crosley CDG7700LW1: Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Plastic cap cover for dryer installation. Replaces cracked, broken, or missing covers. Snaps into place to provide clean finished appearance.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Dryer duct that routes hot air through the ventilation system. Replace if cracked, warped, scorched, or causing debris to attach to clothing during cycles.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This door seal creates a tight closure around the appliance door to help keep cold air in and warm air out, improving cooling performance and reducing energy use. Replace a worn seal to restore a proper door seal. What it does

• Forms a continuous gasket around the door edge to block air leaks.
• Helps prevent frost build-up and loss of cooling inside the compartment.
• Can reduce cycling and strain on the compressor when the seal is intact.
• Common symptom: noticeable cold-air leakage, frost near the door, or uneven cooling.

• High-level task; remove the old seal by pulling out the retainer and fit the new seal into the door channel.
• Warm the gasket slightly to help seat it evenly; avoid open flames or excessive heat.
• Inspect door frame and retainer for damage before installing the new seal.

The Moisture Sensor is an OEM part for Frigidaire dryers. This essential component detects the moisture level in the dryer drum during a drying cycle. It plays a crucial role in determining the optimal drying time, preventing over-drying or under-drying of clothes.

A faulty moisture sensor can be caused by various factors. Over time, the sensor may become coated with lint or residue, affecting its accuracy. Additionally, electrical malfunctions or physical damage can lead to sensor failure.

Symptoms of a bad moisture sensor may include:

• Clothes that are still damp or excessively dry after a drying cycle.
• The dryer stops prematurely or runs for an extended period.
• Error codes related to moisture detection.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Mounting bracket for dryer installation and support. Secures dryer components in place. Replace if bracket is cracked, bent, broken, or missing.

Replacement base for your dryer. Supports the cabinet and internal components. Needed when original is cracked, rusted, or structurally damaged.

Mounting bracket for dryer installation. Secures components in place during operation. Replace if bent, cracked, or missing to ensure proper alignment.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

A compressor protector that helps prevent electrical damage to the refrigerator compressor and supports reliable start-up. Replaces a failed protector to help restore normal compressor operation and reduce risk of repeated motor startups. What it does

• Prevents compressor damage by interrupting power during electrical faults or overloads.
• Supports proper compressor start-up so the fridge can maintain cooling.
• Common symptom fixes: compressor not starting, refrigerator not cooling, or repeated clicking/cycling at start.
• Works with the compressor relay/start components to ensure safe operation.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access usually requires removing the refrigerator back panel or service access panel to reach the compressor area.
• Handle electrical terminals carefully; confirm correct orientation and secure connections.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

Wire harness that connects control board, sensors, and electrical components in your dryer. Replace if wires are damaged, connectors are broken, or worn.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.