Parts for Bosch WTE86300US/03: Cabinet Parts

Front panel case for your dryer. This structural component covers the front of the cabinet. Replace if cracked, damaged, or showing wear from use.

Sealing ring creates airtight barrier to prevent leaks in your dryer. Replace when worn or cracked to restore proper seal. Verify fit with your model.

This heating element replaces the dishwasher's wash water heater to restore normal wash and dry performance. It heats incoming water for better cleaning and helps reduce moisture left in dishes after a cycle. What it does:

• Heats dishwasher wash water to improve detergent activation and soil removal
• Supports dishwasher drying by raising interior temperature during/after the cycle
• Common symptom: dishwasher not heating water or dishes not drying properly
• Common symptom: longer-than-normal cycles or decreased cleaning performance

• Disconnect power and water before beginning repair; this part requires access to the lower tub/pump area
• Inspect and replace any tub gaskets or seals if they are damaged or leaking when reassembling
• Verify electrical connections are secure and test for continuity with a multimeter before and after installation
• If you see corrosion or other damage to mounting hardware, replace affected components to ensure a safe, watertight fit

The Limiter-Temperature is an OEM component specifically designed for select Bosch vented dryers requiring controlled heat. As a safety device, it restricts air exiting the exhaust to prevent accidental ignition of accumulated lint.

Precisely calibrated mechanothermal links automatically trip circuit breakers upon exceeding preset levels. Isolated housings shield reactive alloys from moisture while enabling thermodynamics to naturally trigger protective functions. 

Causes requiring replacement involve over-heating from sustained over-drying preventing auto-stops. Physical damage exposing reactive cores could also impair intended response times.

Symptoms signaling the need for a new temperature limiter include:

• Inability to sense rising exhaust temperatures activating cutoffs
• Constantly energized heating elements lacking temperature regulation  
• Excessively long or uncontrolled dry cycles posing combustion risks

This OEM Bosch replacement component is also compatible with some Gaggenau, Thermador, and select Kenmore dryers employing sensitive temperature cutoffs. Correct installation restores critical overheat protection circuits.
 

Dryer won't heat or overheats? This thermal cutoff limiter cuts power to the heating element when temperature exceeds safe limits. Moderate DIY repair.

This high-temperature 220V, 15-watt oven light bulb restores bright interior lighting so you can monitor cooking progress without opening the door. It's built for sustained heat and replaces a burned-out or flickering lamp.

• Illuminates the oven cavity during baking, broiling, and cleaning cycles
• High-temperature design for continuous heat exposure
• Common failure symptoms: no light when switched on, dim or intermittent illumination, blackened glass, or a broken filament

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/cover; unthread and remove the old bulb
• Thread in the new bulb of the same voltage and wattage; do not overtighten
• Reinstall the cover, restore power, and test the light

Replace your dryer's duct if cracked, damaged, or missing. This duct channels air through the system for proper ventilation and efficient drying performance.

Dryer won't start or door won't stay closed? This door latch assembly secures the door during operation, allowing cycles to run. Moderate DIY repair.

Dryer door seal creates an airtight barrier to retain heat and improve efficiency. Replace if torn, cracked, or causing heat loss. Verify fit with your model.

Thermister

Replace your dryer door seal to stop air leaks and improve drying efficiency. Install when you notice tears, gaps, or lint escaping. Verify fit with your model.

Captures lint and debris during drying cycles. Replace if damaged, torn, or clogged to restore airflow and drying efficiency. Verify fit with your model.

Structural holder component for dryers. Secures internal parts in proper position. Replace if broken, cracked, or missing to restore proper fit.

Dryer cover restores a secure closure over openings, protecting internal components. Replace when cracked, broken, or missing to maintain fit and appearance.

Seals the gap between your dryer door and drum to contain heat and prevent lint escape. Replace if torn, cracked, or causing longer dry times.

The Wheel is an OEM part for Bosch clothes dryers. It is an essential component that works with the drum to tumble clothes, facilitating effective drying action during cycles.

Wheels can cause shorts and come loose over time from heavy drum usage, leading to:

• Vibrating, shaking noises 
• Difficulty spinning the dryer drum by hand
• Stretching or pilling of clothes  
• Unerwven drying performance

Causes of a faulty wheel tend to be wear and tear over time from carrying heavy loads inside a spinning drum. Foreign objects inside the drum can also potentially cause damage.

It is also compatible with some Thermador, Gaggenau, and Kenmore dryer models.

Dryer won't start or shows error codes? A faulty cable harness disrupts electrical connections. This internal wiring assembly restores communication.

If your dryer isn't drying efficiently or has moisture buildup, the air channel may need replacement. Guides airflow for proper venting and performance.