Parts for Crosley CRSH232PS3: Cabinet Parts

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Fix refrigerator lights that won't turn on when door opens. This door light switch is a simple snap-in replacement. Easy 10-minute DIY repair.

Fix a refrigerator light that won't turn on or off when the door opens or closes. This door-activated light switch is a simple 5-minute DIY repair.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Hinge component that guides the cam for self-closing door action. Replace if cracked, broken, or worn to restore smooth door swing and proper alignment.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Lower hinge bracket mounts at the bottom of your refrigerator cabinet to support and align the door. Replace if bent, cracked, or worn for proper alignment.

Supports and aligns the refrigerator door at the bottom pivot point. Replace if bent, cracked, or worn to restore proper door alignment and movement.

Protects cabinet corners from chips and moisture damage. Replace when trim is cracked, missing, or no longer seals properly. Verify fit with your model.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Upper door hinge for refrigerator fresh food and freezer doors. Replaces broken, bent, cracked, or missing hinges from moving or wear.

White plastic hinge cover that snaps onto your refrigerator door hinge. Replace if cracked, broken, or discolored to restore a clean appearance.

Black plastic cover that snaps over the top door hinge on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Replacement screw for refrigerator panels, brackets, and covers. Secures interior and exterior components. Needed when original is missing, stripped, or corroded.

Mounting channel for refrigerator side shelves. Installs on the interior wall to support adjustable shelves. Replace if cracked, broken, or missing.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

This kickplate grille mounts across the bottom front of your refrigerator, covering the lower opening. Replace if cracked, broken, or missing.

Lower front grille that covers the machine compartment while allowing airflow. Replace if cracked, broken, or missing to restore a clean look.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Directs cold air from the freezer to the ice maker assembly. Replace if the duct is cracked, broken, or blocking proper airflow to your ice maker.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Color: White

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.