Parts for Electrolux E32AF75FPS2: 05 - Cabinet Parts

Reduces odors from onions, garlic, fish, and spoiled food using activated carbon and baking soda. Replace every 6 months for fresh air. Confirm fit by model.

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

LED light bulb illuminates refrigerator and freezer compartments for easy food visibility. Replace when dim or burned out. Verify fit with your model.

Fix intermittent refrigerator operation caused by worn or heat-damaged component sockets. This receptacle restores secure plug-in connections for reliable performance.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

This replacement door bin mounts on the inside of your refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or loose bin restores safe, usable storage and helps keep items organized and accessible.

• Provides storage on the door to keep bottles and jars upright
• Restores capacity when the original bin is cracked, warped, or missing
• Helps prevent items from tipping or falling when the door opens/closes
• Common symptoms: bin falls off, won't stay seated, or has broken tabs/cracks

What's included: 1 door bin Install notes:

• Remove all items from the old bin; lift straight up to release from the door slots
• Align the new bin's tabs with the slots and press down until fully seated
• Do not force; re-align if resistance is felt to avoid damaging the door liner
• Place in the correct door position for your model; some bins aren't interchangeable between levels

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

Alignment sleeve bushing maintains smooth part movement in freezers and refrigerators. Replace when worn to eliminate play and restore operation.

Replace your freezer's light lens cover when cracked, yellowed, or missing. Protects the interior bulb from moisture and damage. Verify fit with your model.

Light shield cover for freezer interior. Protects bulb and provides diffused lighting. Replace if cracked, broken, or missing. Snaps into place.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Restores the finished edge on your refrigerator cabinet and hides gaps. Replaces cracked, broken, or missing corner trim for a cleaner appearance.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Specs: Hex head ,1/4-20 x 5/8

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

Bottom front grille that covers the lower compartment while allowing airflow. Replace if cracked, broken, or missing to restore a finished appearance.

Hex washer head screw secures hinges, panels, and trim to your freezer or refrigerator. Replace missing, stripped, or corroded screws for stable parts.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Mounting bracket that secures freezer shelves and internal panels. Replace if cracked, bent, or broken to restore proper alignment and stability.

Guide rail that supports and directs refrigerator drawers along their track. Replace when original is worn, cracked, or broken to restore smooth sliding.

Replacement drawer slide for freezers. Restores smooth gliding when original is broken, worn, or causes sticking. Essential for proper drawer alignment.

Supports and guides the crisper drawer for smooth sliding. Replace if cracked, broken from stress, or if drawer no longer sits securely in refrigerator.

Replacement mounting screw for freezer panels, trim, and brackets. Needed when original fastener is missing, stripped, or damaged during repairs.