Parts for Frigidaire FGUS2632LP2: 07 - Cabinet Parts

Replace your refrigerator water filter every 6 months to maintain fresh-tasting water and remove impurities like lead and chlorine. Confirm fit by model.

This air duct cover installs inside your refrigerator to protect and conceal the air circulation duct. Replace if cracked, broken, or missing.

Interior cover that shields the evaporator coil assembly and directs airflow. Replace if cracked, broken, or missing to protect internal components.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Interior light won't turn on or off? This refrigerator light switch controls the lamp circuit. Easy DIY fix restores reliable lighting control.

Fix a refrigerator light that won't turn on or off when the door opens or closes. This door-activated light switch is a simple 5-minute DIY repair.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Replacement door closer cam for refrigerator hinges. Installs on upper door hinge to control door swing and prevent cabinet damage. Needed when cracked or worn.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Lower door hinge for side-by-side refrigerators. Secures and pivots the door for smooth opening. Replace if cracked, broken, or causing door sag.

Lower door hinge secures the bottom corner of your refrigerator door and provides a pivot point for smooth opening and closing. Replace if cracked or worn.

Protects cabinet corners from chips and moisture damage. Replace when trim is cracked, missing, or no longer seals properly. Verify fit with your model.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Supports and aligns the refrigerator door at the hinge pivot point. Replace if cracked, bent, or worn to restore stable door operation and proper sealing.

Plastic trim cap that snaps over the top door hinge. Replaces cracked, broken, or missing hinge covers to protect the mechanism and restore a clean look.

Upper hinge cover for refrigerators. Conceals and protects the top door hinge assembly. Replace if cracked, broken, discolored, or missing.

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

This electronic control board manages your refrigerator's key functions including temperature control, defrost cycles, and display operations. It processes input from sensors and user settings to maintain proper cooling performance. Replace this part if temperature control is erratic, the display is blank, or cooling functions stop working.

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Genuine mounting screw secures panels, brackets, and covers inside your refrigerator. Replace missing, stripped, or corroded fasteners to restore secure fit.

Replaces damaged or missing lower front kickplate grille on side-by-side refrigerators. Restores finished appearance and protects area beneath doors.

This part number contains one (1) screw.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Directs cold air from the freezer to the ice maker assembly. Replace if the duct is cracked, broken, or blocking proper airflow to your ice maker.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.