Parts for Frigidaire GHSC239TDB0: 07 - Cabinet Parts

Reduces chlorine taste and odor while filtering sediment from your refrigerator's water and ice. Replace every 6 months for best performance. Verify fit.

Plastic cover that protects the evaporator coil in your refrigerator. Replace if cracked, broken, or missing to restore proper airflow and protection.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Replacement cam riser for refrigerator door hinges. Installs at the top hinge assembly. Replace if cracked, broken, or worn to restore smooth door operation.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Mounting channel that secures refrigerator shelves to interior walls. Replace if cracked, broken, or no longer holding shelves securely in place.

This genuine OEM part is the main control board for refrigerators. The main control board is the primary circuit board that controls the refrigerator's essential functions of maintaining and controlling temperature. If the refrigerator is no longer staying cool, powering on, or maintaining proper temperature, the main control board will need to be replaced. Luckily, this is a fairly simple repair.To begin, start by unplugging the refrigerator. Once unplugged, proceed to uninstall the inner door panel of the refrigerator by removing the mounting screws. Once removed, access the old control board. Remove the wire harness and any individual wires attached to the old board. After that, pull the old board out of its mounting brackets to fully remove it from the refrigerator. Reinsert the wires into their correct terminals on the new board and snap it into its mounting brackets. Once secured, reinstall the inner panel of the refrigerator and restore power to the appliance. This authentic replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Fix inconsistent cooling or freezer frost buildup with this refrigerator air damper assembly. Controls airflow between compartments. Moderate DIY repair.

Covers the bottom front of your refrigerator. Replace if cracked, broken, or missing. Clips into place at the base to restore appearance.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Color: White