Parts for Frigidaire GLHS65EHSB3: 07 - Cabinet Parts

Reduces chlorine taste and odor while filtering sediment from your refrigerator's water and ice. Replace every 6 months for best performance. Verify fit.

This air duct cover installs inside your refrigerator to protect and conceal the air circulation duct. Replace if cracked, broken, or missing.

Interior cover that shields the evaporator coil assembly and directs airflow. Replace if cracked, broken, or missing to protect internal components.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Fix a refrigerator light that won't turn on or off when the door opens or closes. This door-activated light switch is a simple 5-minute DIY repair.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Replacement cam riser for refrigerator door hinges. Installs at the top hinge assembly. Replace if cracked, broken, or worn to restore smooth door operation.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Upper door hinge for refrigerator fresh food and freezer doors. Replaces broken, bent, cracked, or missing hinges from moving or wear.

Black plastic cover that snaps over the top door hinge on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Replacement screw for refrigerator panels, brackets, and covers. Secures interior and exterior components. Needed when original is missing, stripped, or corroded.

Mounting channel for refrigerator side shelves. Installs on the interior wall to support adjustable shelves. Replace if cracked, broken, or missing.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Covers the bottom front of your refrigerator. Replace if cracked, broken, or missing. Clips into place at the base to restore appearance.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Directs cold air from the freezer to the ice maker assembly. Replace if the duct is cracked, broken, or blocking proper airflow to your ice maker.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Color: White