Parts for Frigidaire LGUI1849LP1: 05 - Cabinet Parts

Plastic cover that protects the evaporator fan and directs airflow in your refrigerator. Replace if cracked, broken, or missing to restore proper airflow.

Controls airflow between freezer and fresh food compartments. Attaches to the damper control shaft. Replace when cracked, stripped, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Front evaporator fan motor mounting bracket

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. This DIY repair takes 10-15 minutes with basic tools.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Replace your refrigerator's interior light bulb when it burns out to restore visibility. Easy screw-in installation. Verify fit with your model number.

Replace your refrigerator light socket when bulbs won't illuminate or burn out quickly. Provides secure bulb connection and prevents overheating. Verify fit.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Lower hinge bracket secures the refrigerator door at the bottom, allowing smooth pivoting. Replace if bent, cracked, or causing door misalignment and sagging.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Restores the finished edge on your refrigerator cabinet and hides gaps. Replaces cracked, broken, or missing corner trim for a cleaner appearance.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

White plastic cover that snaps onto the upper door hinge. Replace if cracked, broken, or missing to restore a finished look to your refrigerator.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Decorative panel at the base of your refrigerator that provides ventilation access. Replace if cracked, broken, or missing. Snaps into place easily.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Protective cardboard or plastic cover that installs over the internal cooling system and wiring. Replace if cracked, torn, ripped, or missing.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Refrigerator interior light won't turn on or stays on? This door light switch controls your fridge lighting. Quick DIY fix with basic tools.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.