Parts for Kenmore 253.21042413 (25321042413, 253 21042413): Cabinet Parts

A removable cap that covers the freezer's defrost drain hole, typically located at the bottom rear of the freezer compartment. Replace when water pools in the freezer, the cap is missing, or ice blocks the drainage system.

Freezer won't turn on or keeps tripping? This circuit breaker protects your freezer's electrical system. Direct replacement part for upright models.

Freezer won't turn on or keeps tripping? This circuit breaker protects your appliance from electrical overload. Simple 10-15 minute fix for most models.

Freezer won't run or keeps shutting off? This resettable circuit breaker protects against electrical faults. Resets after power interruption. Easy DIY fix.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

LED light bulb illuminates your refrigerator interior. Replace when bulb burns out, flickers, or stops working. Verify fit with your model number.

Interior light not working? This light socket provides the electrical connection for your freezer bulb. Simple DIY fix restores compartment lighting.

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

Replacement control housing cover for freezers. Snaps over the control panel assembly. Replace if cracked, broken, or missing to restore appearance.

Freezer not holding temperature or running too warm? This temperature control regulates freezer temperature. Moderate DIY repair restores proper cooling.

Secures the temperature sensing tube to the thermostat for accurate temperature control. Replace if loose, missing, or damaged to prevent erratic cooling.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Drain hose that channels wastewater from your freezer to the household drain. Replace if cracked, clogged, or leaking to restore proper drainage.

Alignment sleeve bushing maintains smooth part movement in freezers and refrigerators. Replace when worn to eliminate play and restore operation.

Replacement light shield that covers and protects the interior bulb in your refrigerator. Install when the original lens is cracked, broken, or missing.

Cabinet corner trim piece for freezers. Covers and finishes the corner edge of the cabinet exterior. Replace if cracked, chipped, or missing.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Specs: Hex head ,1/4-20 x 5/8

Wire storage basket for upright freezers. Holds and organizes frozen food items. Replace if your original basket is bent, damaged, or missing.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

This kickplate grille covers the lower front opening of the oven cabinet, protecting internal components and directing vent airflow while maintaining a finished look for the range. Restores proper vent appearance and protects against debris. What it does:

• Covers the lower front vent opening and channels airflow from the oven cavity
• Protects internal components from dust, debris and accidental contact
• Replaces cracked, bent or missing kickplate trim that affects appearance
• Helps maintain proper ventilation clearance at the oven base

• One kickplate grille

• Disconnect power to the appliance before beginning work
• Remove the lower access drawer or panel per your manual to access mounting points
• Align grille tabs or screw holes, then secure with the factory fasteners (do not overtighten)

Panel-mounted indicator light that illuminates when functions are active. Replace when dim, flickering, or burned out to restore clear status visibility.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

Mounting screw for freezers and refrigerators. Secures internal components, panels, or shelving. Replace if stripped, missing, or damaged during repairs.

Foam insulation sleeve that wraps around the defrost drain tube. Replace if worn, missing, or damaged to prevent condensation and maintain proper insulation.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.