Parts for Kenmore 253.22742411 (25322742411, 253 22742411): Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Fixes uneven cooling or warm top shelves in freezers. This blower wheel restores proper air circulation when the fan stops moving cold air effectively.

Freezer won't turn on or keeps tripping? This circuit breaker protects your appliance from electrical overload. Simple 10-15 minute fix for most models.

Freezer won't run or keeps shutting off? This resettable circuit breaker protects against electrical faults. Resets after power interruption. Easy DIY fix.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

LED light bulb illuminates your refrigerator interior. Replace when bulb burns out, flickers, or stops working. Verify fit with your model number.

Interior light not working? This light socket provides the electrical connection for your freezer bulb. Simple DIY fix restores compartment lighting.

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Access panel cover that protects internal components and provides a finished look. Replace if the original is cracked, broken, or missing from your appliance.

Freezer won't shut off or runs continuously? A faulty temperature control thermostat is often the cause. Simple DIY fix in about 30 minutes with a screwdriver.

Secures the temperature sensing tube to the thermostat for accurate temperature control. Replace if loose, missing, or damaged to prevent erratic cooling.

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

Collects defrost water beneath your freezer. Replace if cracked, broken, or missing to prevent leaks. Installs in the bottom compartment under the unit.

Alignment sleeve bushing maintains smooth part movement in freezers and refrigerators. Replace when worn to eliminate play and restore operation.

Replacement light shield that covers and protects the interior bulb in your refrigerator. Install when the original lens is cracked, broken, or missing.

Cabinet corner trim piece for freezers. Covers and finishes the corner edge of the cabinet exterior. Replace if cracked, chipped, or missing.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Specs: Hex head ,1/4-20 x 5/8

This tempered glass refrigerator shelf replaces a damaged or missing shelf to restore stable, easy-to-clean storage for food and containers. Designed for direct fit where this OEM shelf is specified. What it does

• Provides a flat, sturdy surface for storing food, containers and produce.
• Helps organize interior storage and prevents items from shifting or spilling.
• Smooth glass surface resists stains and wipes clean quickly.
• Replaces shelves that are cracked, chipped or missing.

• Remove food and any items from the area before installing.
• Handle shelf carefully—wear protective gloves to avoid cuts from broken glass.
• Sit the shelf into existing support rails or clips and ensure it is fully seated on both sides.
• Replace damaged support clips or rails before installing the new shelf.

Wire shelf for upright freezers. Installs by inserting side pegs into wall holes. Replace cracked, broken, or missing shelves or add extra storage.

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

Storage basket for upright and freestanding freezers. Installs inside the freezer compartment to organize frozen items. Replace if cracked, broken, or missing.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

This kickplate grille covers the lower front opening of the oven cabinet, protecting internal components and directing vent airflow while maintaining a finished look for the range. Restores proper vent appearance and protects against debris. What it does:

• Covers the lower front vent opening and channels airflow from the oven cavity
• Protects internal components from dust, debris and accidental contact
• Replaces cracked, bent or missing kickplate trim that affects appearance
• Helps maintain proper ventilation clearance at the oven base

• One kickplate grille

• Disconnect power to the appliance before beginning work
• Remove the lower access drawer or panel per your manual to access mounting points
• Align grille tabs or screw holes, then secure with the factory fasteners (do not overtighten)

Panel-mounted indicator light that illuminates when functions are active. Replace when dim, flickering, or burned out to restore clear status visibility.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

Mounting screw for freezers and refrigerators. Secures internal components, panels, or shelving. Replace if stripped, missing, or damaged during repairs.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.