Parts for Universal Multiflex (Frigidaire) MRTW20V5PW3: Cabinet Parts

Plastic cover that protects the evaporator fan and directs airflow in your refrigerator. Replace if cracked, broken, or missing to restore proper airflow.

Controls airflow between freezer and fresh food compartments. Attaches to the damper control shaft. Replace when cracked, stripped, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Front evaporator fan motor mounting bracket

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Size: 1" round

Plastic plug insert for refrigerator panels and structural openings. Replace if cracked, broken, or missing to maintain proper cabinet appearance.

Seals unused holes in refrigerator cabinet or liner. Prevents drafts, moisture, and pests from entering through open fittings. Restores clean appearance.

Color: White

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

Lower hinge bracket secures the refrigerator door at the bottom, allowing smooth pivoting. Replace if bent, cracked, or causing door misalignment and sagging.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Protects cabinet corners from chips and moisture damage. Replace when trim is cracked, missing, or no longer seals properly. Verify fit with your model.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

White plastic cover that snaps onto the upper door hinge. Replace if cracked, broken, or missing to restore a finished look to your refrigerator.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Decorative panel at the base of your refrigerator that provides ventilation access. Replace if cracked, broken, or missing. Snaps into place easily.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Replacement front roller assembly for refrigerators. Includes leveling screw. Needed when roller is cracked, broken, or leveling screw is bent or damaged.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.