Parts for Electrolux EIFLS55QT0: Cabinet / Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replace your washer's cracked or missing access cover. Restores exterior protection, shields internal components from dust and moisture, and provides a clean finished appearance.

Mounting bracket for dryer assemblies. Secures components in place during operation. Replace if bracket is bent, cracked, broken, or missing.

Mounting bracket for dryer installation. Secures components in place. Replace if bent, cracked, broken, or missing to restore proper support and fitment.

Fix a washer that won't start or run because the door won't lock. This door lock assembly secures the door during wash cycles. DIY-friendly repair.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This inner oven door glass restores the viewing window and helps contain heat inside the cavity for even cooking. Use when the door glass is cracked, broken, cloudy, or otherwise damaged to restore safe, usable viewing. What it does:

• Replaces cracked, chipped, shattered, or cloudy inner oven door glass.
• Restores a clear view of the oven interior so you can monitor cooking without opening the door.
• Helps maintain the oven's sealed cavity to reduce heat loss during cooking.
• Prevents loose or broken glass from falling into the oven cavity.

• Allow the oven to cool completely and disconnect power before starting service.
• Handle glass with heavy gloves and eye protection; broken glass can be sharp.
• Reinstall or replace any door screws, brackets, or gaskets exactly as removed; follow the oven manufacturer's service instructions.

Outer cabinet trim frame that secures and finishes the appliance front panel. Replace this structural part if damaged, bent, or cracked to restore fit.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

The Washer Door Strike Assembly is an OEM part for Frigidaire washing machines. It is designed to engage with the door latch to ensure the door stays securely closed during operation. This component is critical for the safety and efficiency of the washer, as it prevents the door from opening mid-cycle, which could result in water leaks and operational interruptions.

You should replace the door strike assembly if it becomes faulty. Causes of a bad door strike can include regular wear and tear, physical damage from forcefully closing the door, or misalignment that prevents it from engaging properly with the latch. A malfunctioning door strike can lead to the washer not starting or stopping mid-cycle.

Symptoms of a bad washer door strike assembly include:

• The washer door not latching or locking properly
• The washer not starting or stopping mid-cycle
• Error codes related to door lock issues
• The door feeling loose or not securing tightly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Genuine screw fastener for securing dryer panels, brackets, and internal components. Replace when stripped, missing, or corroded to restore tight fit.

Secures hoses in your laundry center. Replace if cracked, loose, or causing leaks. Confirm fit with your model number before ordering.

Replacement fastener screw for dryers, washers, and laundry centers. Secures panels, brackets, and assemblies to the appliance frame. Needed when missing.

Spring mounting bracket for washers. Secures suspension springs to the washer tub or frame. Replace if bracket is cracked, bent, or broken from load stress.

This is a genuine replacement screw used to secure appliance panels and components. It provides a simple, reliable fix for loose or missing fasteners so panels and parts stay properly attached. What it does:

• Fastens panels, brackets, or components in place to restore original fit
• Replaces missing or stripped screws that cause rattling or loose parts
• Matches OEM thread and head style for correct seating and torque
• Helps eliminate vibration-related noise by securing loose pieces

• One replacement screw as shown

• Inspect mating threads and clear any debris before installing the new screw
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can damage threads or parts
• Disconnect power and follow appliance safety guidelines before servicing

Back panel for laundry centers and washers. Covers the rear exterior housing. Replace if cracked, damaged, or missing to restore appearance and protect internal components.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Power cord for washer installations. Replace if your original cord is damaged, frayed, missing, or shows exposed wiring for safe appliance operation.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Support bracket for dryer assembly. Mounts and secures internal components in place. Replace if cracked, bent, broken, or missing to restore proper fit.

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

Sleeve bearing bushing that supports rotating shafts in washers. Replace if worn, cracked, or causing noise. Reduces friction and centers components.

Replacement mounting nut that secures panels, trim, and internal components. Needed when original nut is stripped, corroded, missing, or lost during repair.

This trim ring is a replacement surface trim piece that restores the finished look and edge around the appliance opening. It provides a clean, secure edge and replaces bent, cracked, or missing trim to improve appearance and fit. What it does

• Covers and finishes the exposed edge of the appliance opening for a clean appearance
• Secures and aligns adjacent components by providing a stable mounting edge
• Addresses cosmetic damage such as dents, cracks, or paint loss around the opening
• Helps prevent small items from getting caught in the exposed edge

• One trim ring

• Disconnect power to the appliance before starting any repair
• Removal typically requires loosening mounting screws or clips; keep hardware for re-use unless damaged
• Handle edges carefully; part and surrounding metal may be sharp
• If the trim mounts to or around other components (elements, panels), support those parts during removal and reinstallation

Secures dryer panels and components to maintain proper alignment and stability. Replace when the original clip is broken, loose, or missing.

Spring protector installs on washer suspension springs to prevent wear and damage. Replace if cracked, broken, or missing to protect suspension components.

Sound dampening insulation that reduces vibration and noise in your washer. Replace if worn, torn, or missing to restore quiet operation and protect components.

This replacement cover restores the protective barrier and finished look of the original part. It shields the underlying assembly from dust and accidental contact, helping maintain safe operation and a clean, factory appearance.

• Provides a protective barrier over the designated opening or component
• Helps maintain proper airflow/enclosure integrity as designed
• Secures with existing tabs or screws for a stable fit
• Typical signs of failure: cracked or missing cover, broken tabs, loose/rattling panel, visible damage

• Disconnect power before service; for laundry appliances, also shut off water and gas
• Wear gloves; retain and reuse original screws/clips unless new hardware is supplied
• Note orientation before removal and transfer any clips, seals, or trim from the old cover
• Seat fully and avoid overtightening; verify clearances before restoring power

Replaces a cracked, scratched, or cloudy outer door lens. This clear plastic panel forms the exterior of your dryer's door window for visibility into the drum.

Replaces a cracked, scratched, or cloudy outer door lens. This clear plastic panel forms the exterior of your dryer's door window for visibility into the drum.

Replacement access panel cover for dryers and laundry centers. Shields internal components from dust and debris. Replaces cracked, broken, or missing panels.

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Replace a worn, broken, or missing washer cabinet damper to restore smooth counterweight action and controlled movement. Installs on cabinet assembly.

This small plastic retainer clip secures trim and lightweight components so doors and shelves stay aligned and rattle-free. A simple replacement that restores proper fit where a broken or missing clip lets parts shift. What it does

• Fastens and aligns lightweight plastic trim, door, or shelf components
• Prevents movement and noise caused by a cracked or missing retainer
• Restores secure fit for loose or sagging trim pieces
• Commonly used where a push-in or snap-in fastener is required

• One retainer clip

• Inspect the mating slots or holes for damage before installing the new clip
• Push the clip into place until it snaps; the attached part seats securely
• No special tools typically required; use a flat tool to remove the old clip if needed
• Disconnect power only when working near electrical components or lighting assemblies

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.