Parts for Ge PVS21KSEBFSS: Case Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Secures the hinge cover to your refrigerator door or cabinet hinge. Replace this screw if it's missing, stripped, or damaged to stop the cover from loosening.

Replacement mounting screw for refrigerator brackets, panels, and handles. Restores secure fit when original fastener is missing, stripped, or damaged.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

Fix inconsistent cooling or excess moisture in your refrigerator with this humidity sensor. Direct replacement part restores proper climate control.

Protective housing cover for refrigerator humidity sensor. Replaces cracked, broken, or missing covers. Installs in fresh food compartment.

Fix inconsistent cooling or frost buildup with this refrigerator humidity sensor. Monitors moisture levels to optimize defrost cycles. Direct replacement.

Right-hand center hinge assembly restores door alignment and smooth operation. Replace when doors sag or don't seal properly. Verify fit with your model.

Adjustable hinge pin that installs in the door hinge bracket to provide a pivot point. Replace when worn, loose, or damaged to restore door alignment.

Replace a cracked, broken, or missing refrigerator hinge cover. This plastic trim piece installs over the hinge mechanism for a clean, finished look.

Replacement closure spring for refrigerator doors and panels. Installs at hinge points to provide smooth closing action. Needed when original is broken, stretched, or missing.

Replace the corner cap cover on your refrigerator. This plastic cover protects and finishes the corner edge. Order a new one if cracked or missing.

Front roller assembly for refrigerators. Mounts to the base to enable smooth movement and leveling. Replace if cracked, worn, or mobility is impaired.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

The refrigerator leveling screw is an adjustable threaded leg located at the bottom corner of your refrigerator that lets you raise or lower that corner to achieve a level, stable position. Proper leveling ensures the doors swing shut on their own and that the refrigerator runs efficiently. Replace or adjust this part if your refrigerator rocks on the floor, the doors won't stay closed, or you notice uneven gaps around the door seals.

Leg bracket assembly for refrigerators. Mounts to the base to secure and support adjustable legs. Replace if cracked, bent, or broken to restore stability.

The GE Door Light Switch is an OEM Replacement Part that serves as the Freezer Door Fan and Light Switch. The switch is made from metal, wiring, and plastic. It plays an essential role in energy conservation by turning off the light when the refrigerator or freezer door is closed

Over time, the door light switch can wear out or fail due to frequent use, exposure to moisture, or electrical issues. When this happens, the interior light may not function correctly, which can hinder visibility inside the refrigerator.

Symptoms of a bad door light switch may include:

• Interior light not turning on when the door is opened
• Interior light not turning off when the door is closed
• Flickering or intermittent operation of the interior light

This switch is compatible with select GE and Hotpoint models.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Size: 10-32 GXTT FLP.595 S

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.

This washer hinge secures and guides the lid on top-load washers so the lid opens and closes smoothly and stays aligned. It restores proper lid fit and reduces wobble or misalignment during use. What it does

• Supports the washer lid pivot point for smooth opening and closing
• Keeps the lid aligned to prevent rubbing, binding, or uneven gaps
• Reduces lid movement and noise caused by a worn or damaged hinge
• Helps maintain safety by ensuring the lid closes fully when not in use

• One washer hinge

• Disconnect power before beginning any repair to avoid shock or injury
• Remove the washer lid or access panel per the service instructions to reach the hinge
• Transfer any mounting hardware or hinges in the correct orientation; tighten fasteners securely
• Test lid operation after installation; recheck alignment and fasteners