Parts for Whirlpool TU950QPXB1: 04 - Container Parts

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

This actuator is the small mechanism that drives the dishwasher's detergent dispenser door, releasing detergent at the correct time in the cycle for consistent cleaning performance. What it does:

• Converts a control signal into movement to open the dispenser door
• Helps ensure detergent is released at the proper stage of the wash
• Wear or breakage can leave the cup closed or only partially opened
• Common symptoms: detergent left in cup after cycle, dispenser door not opening, or visible damage to the lever

• 1 actuator

• Disconnect power at the breaker before servicing
• Open the door and remove the inner door panel to access the dispenser assembly
• Note the actuator's orientation; transfer and seat it fully in the mechanism
• Reassemble the door, restore power, and run a short cycle to confirm proper dispenser operation

Stainless steel control panel for trash compactor front console. Replaces scratched, dented, or damaged panel. Provides mounting surface for controls.

Replacement drawer container for trash compactors. Installs as the main compartment to hold contents securely. Needed when original is cracked, broken, or deformed.

Replacement foot pedal for trash compactors. Installs at the base to operate the door release mechanism. Replace if cracked, broken, or missing.

Size: 8-32 x 3/8 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Positions and secures your trash compactor door handle for proper alignment. Replace if cracked, missing, or worn to prevent handle rubbing or binding.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

This replacement refrigerator door handle provides a secure grip and restores proper opening and closing of the appliance door. Designed to match the original fit and finish for a clean, factory look. What it does:

• Replaces a cracked, broken or missing refrigerator door handle
• Restores a solid grip so the door opens and closes normally
• Prevents further damage from using makeshift grips or tape
• Helps keep the door aligned and sealed by providing proper leverage

• Disconnect power to the appliance or unplug the unit before starting work to avoid electrical hazard.
• Remove food and shelves from the door as needed for access and to prevent breakage.
• Use the correct screwdriver or socket to remove mounting screws; support the handle during removal and installation.
• If the handle attaches with hidden clips, work carefully to avoid breaking plastic retainers.

Size: 8-18 x 1/2 inch.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Replacement roller bearing for trash compactor drawers. Installs on tracks to support smooth gliding. Replace worn or damaged bearings for easier operation.

Size: 3\8-24 inch.

Protective guard for trash compactors. Shields internal components from debris and impact. Replace if cracked, broken, or missing to maintain proper function.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.