Parts for Kitchenaid KUCS03FTWH3: 05 - Container Parts

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

This actuator is the small mechanism that drives the dishwasher's detergent dispenser door, releasing detergent at the correct time in the cycle for consistent cleaning performance. What it does:

• Converts a control signal into movement to open the dispenser door
• Helps ensure detergent is released at the proper stage of the wash
• Wear or breakage can leave the cup closed or only partially opened
• Common symptoms: detergent left in cup after cycle, dispenser door not opening, or visible damage to the lever

• 1 actuator

• Disconnect power at the breaker before servicing
• Open the door and remove the inner door panel to access the dispenser assembly
• Note the actuator's orientation; transfer and seat it fully in the mechanism
• Reassemble the door, restore power, and run a short cycle to confirm proper dispenser operation

This actuator is the small mechanism that drives the dishwasher's detergent dispenser door, releasing detergent at the correct time in the cycle for consistent cleaning performance. What it does:

• Converts a control signal into movement to open the dispenser door
• Helps ensure detergent is released at the proper stage of the wash
• Wear or breakage can leave the cup closed or only partially opened
• Common symptoms: detergent left in cup after cycle, dispenser door not opening, or visible damage to the lever

• 1 actuator

• Disconnect power at the breaker before servicing
• Open the door and remove the inner door panel to access the dispenser assembly
• Note the actuator's orientation; transfer and seat it fully in the mechanism
• Reassemble the door, restore power, and run a short cycle to confirm proper dispenser operation

If your compactor buttons aren't responding or the display is blank, the control panel likely needs replacement. Restores full operation and display.

This part is the outer panel for the drawer on a trash compactor. This part protects the wiring and other components inside of the drawer and also provides a decorative finish for the face of the unit.In the event that the stainless steel finish becomes scratched, dented, or damaged in any way, this is a high-quality replacement part. The screws may need to be reused when installing the new part, so keep those in a safe place so they do not get lost. Before replacing this part, unplug the unit from the electrical outlet or turn off the house circuit breaker. Wears gloves for safety during this process.This outer panel is compatible with trash compactors that are manufactured by the Whirlpool and KitchenAid brands. It is sold individually and sourced straight from the manufacturer as a genuine OEM part.

Replacement drawer container for trash compactors. Installs as the main compartment to hold contents securely. Needed when original is cracked, broken, or deformed.

Color: White

Color: Black

This nameplate displays your dishwasher's model information and operating instructions for easy reference. It adheres to the appliance's exterior and provides important safety and usage details. Replace this nameplate if it becomes illegible, peels off, or gets damaged during cleaning.

White foot pedal for trash compactor drawer release. Replaces broken, cracked, or missing pedals. Installs at the base of the compactor unit.

Fix a stuck or difficult-to-open compactor drawer with this replacement foot pedal. Restores hands-free drawer release and smooth latch operation.

Size: 8-32 x 3/8 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Positions and secures your trash compactor door handle for proper alignment. Replace if cracked, missing, or worn to prevent handle rubbing or binding.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

This replacement refrigerator door handle lets you open and close the door with a secure, comfortable grip and restores normal door operation and appearance. Designed to match the original cabinet fit and finish. What it does

• Replaces a cracked, loose, or broken door handle so the door can be opened and closed safely.
• Provides the same grip and leverage as the original part to prevent slippage and damage.
• Restores the refrigerator's exterior appearance when the original handle is scratched or worn.
• Helps prevent further cabinet damage caused by using towels or alternate grips.

• High-level: Remove any interior shelves or panels that block access before starting.
• Use common hand tools; support the door while removing and reinstalling the handle to avoid strain on the hinges.
• Follow manufacturer instructions and tighten fasteners securely but do not overtighten.

This is a replacement refrigerator door handle that restores a secure grip and proper door operation. It replaces a cracked, broken, or worn handle so you can open and close the door safely and confidently. What it does:

• Replaces a damaged or loose refrigerator door handle so the door can be opened and closed normally
• Restores a comfortable, secure grip when pulling the refrigerator door
• Prevents sharp edges and safety hazards from a cracked or broken handle
• Helps maintain proper door alignment and sealing when handle mounting is restored

• One replacement refrigerator door handle

• Designed for straightforward replacement; reinstall using existing mounting hardware when possible
• Disconnect power to built-in lighting/components only if panels or wiring are exposed during installation
• Use appropriate hand tools; avoid overtightening fasteners to prevent damage

This genuine handle assembly replaces a damaged or worn refrigerator door handle so you can open and close the door securely and comfortably. It restores the grip and appearance of the door without replacing the whole door. What it does

• Replaces a cracked, broken, loose, or missing refrigerator door handle
• Restores proper grip and lever action for opening the refrigerator door
• Helps prevent injury from jagged or damaged handle edges
• Returns the door to a finished appearance and functional use

• Disconnect power to the appliance or unplug the refrigerator before any repairs when required by the manufacturer.
• Support the door while removing/installing the handle to avoid straining hinges or tipping.
• Typical installation requires basic hand tools (screwdriver, socket); follow OEM instructions for correct fastener torque and orientation.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Replacement roller bearing for trash compactor drawers. Installs on tracks to support smooth gliding. Replace worn or damaged bearings for easier operation.

This threaded fastener secures components within your trash compactor, ensuring proper alignment and operation of moving parts. It provides a strong mechanical connection that withstands the forces generated during compaction cycles. Replace if components become loose or if the original nut is damaged or missing.

Protective guard for trash compactors. Shields internal components from debris and impact. Replace if cracked, broken, or missing to maintain proper function.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.