Parts for Ge JGB720DEJ2BB: Control Panel & Cooktop Parts

Replace your gas range control knob if cracked, broken, or worn from frequent use. Installs on the control panel to operate burners and adjust flames.

Replacement end support for gas ranges. Provides structural support at the side of the range. Replace if cracked, bent, broken, or missing.

Left front end support bracket for gas ranges. Secures the front corner of the cooktop frame. Replace if cracked, bent, or missing to restore stability.

Fix a loose or sagging control panel with this range control bracket. Secures the control assembly to the frame for stable button operation. Easy install.

Oven won't heat, display goes blank, or controls unresponsive? This electronic control board manages bake/broil cycles and restores full oven operation.

Upper back cover panel for gas ranges. Protects internal components and completes the exterior finish. Replace if cracked, damaged, or missing.

Replacement grate assembly for gas range stovetops. Provides stable cooking surface over burners. Order if your existing grate is cracked, broken, or worn.

This factory fastener secures internal components or panels in your appliance. Replacing a missing or stripped screw restores a snug fit, helps prevent vibration or rattling, and keeps assemblies aligned for proper operation.

• Secures brackets, panels, or internal components to the frame
• Replaces missing, rusted, or stripped hardware
• Helps reduce rattling, vibration, or loose-fit issues
• Maintains proper alignment and fit of assemblies

• Disconnect power before servicing
• Use the correct driver to avoid stripping the screw head
• Install in the original location; match thread and length to the original
• Tighten until snug; do not overtighten, especially into plastic or thin metal

Control panel overlay for your range. Replaces worn, faded, cracked, or peeling overlays on the control panel face. Restores the appearance and readability.

Medium burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn from use.

Burner cap covers the burner head and distributes flame evenly on gas ranges and cooktops. Replace if cracked, warped, or missing for proper cooking.

Burner cap assembly covers the burner head on gas cooktops and ranges. Replace cracked, stained, corroded, or missing caps to restore appearance.

Replacement small surface burner for gas ranges and cooktops. Restores proper flame control when original burner is damaged, cracked, or corroded.

Replacement burner head for gas ranges and cooktops. Installs on stovetop to distribute flame evenly. Replace if warped, cracked, or causing uneven flames.

Oval burner assembly for gas range cooktops. Replace if your burner head or cap is cracked, clogged, damaged, or missing. Includes both burner and cap.

Medium-sized surface burner for gas cooktops and ranges. Installs on the cooktop surface. Replace if cracked, worn, or providing uneven heat distribution.

If your gas range burner won't light or clicks continuously, this igniter clip secures the ignition system. Simple DIY fix in under 15 minutes.

A replacement ground harness that restores the appliance's chassis grounding connection to help ensure safe electrical operation. Installs quickly to replace a damaged or corroded ground lead and reduce risk of arcing. What it does

• Provides the dedicated chassis ground connection between appliance wiring and the cabinet
• Restores proper grounding when original harness is broken, frayed, corroded, or detached
• Helps prevent intermittent power issues, arcing, or nuisance tripping caused by poor ground continuity
• Used wherever a short ground lead or bonded connector is required for safety

• One ground harness as shown

• Disconnect power (unplug or shut off circuit breaker) before starting any repair
• Verify correct grounding point on the cabinet and secure the harness with the original screw or fastener
• Match connectors and routing to the original harness; avoid touching energized terminals during installation

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

This is the flat griddle plate that sits over the center burners on compatible cooktops/ranges. It provides an even cooking surface for pancakes, sandwiches, and more, and replaces a worn or missing griddle so heat is distributed properly.

• Creates a level, flat surface over the center burners for even heating
• Helps improve cooking results when the original griddle is warped, worn, or damaged
• Can reduce sticking and uneven browning compared to a deteriorated plate
• Restores intended fit and stability on the cooktop when the original no longer seats correctly

• Let the appliance cool completely and shut off gas/electric supply before handling
• Lift off existing center grate/griddle once cool; position the new griddle so it seats securely on the designated supports
• Ensure the griddle is stable and clear of burner flames before use
• Season/condition and clean per your range's Use & Care to maintain performance