Parts for Electrolux EFLS517SIW0: 02 - Control Panel Parts

Fix unresponsive buttons or blank displays with this user interface control board. Restores keypad function and display readings on your laundry center.

Replacement mounting bracket that secures panels, assemblies, or controls to your washer cabinet. Needed when original is cracked, broken, or missing.

Control knob assembly for laundry center washers. Replacement needed when knob is cracked, broken, loose, or missing from repeated use or damage.

Fix uneven drying or excess noise with this air flow diffuser. Directs airflow inside your dryer for consistent temperature and quieter operation.

Fix E11 error code and washer not filling issues. This pressure sensor switch monitors water levels and signals the control board. DIY repair in under an hour.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Main Board Assembly is an OEM replacement part for Frigidaire washing machines. It is the central processing unit located inside the control panel that allows the washer to operate as intended.

Causes of a bad main board can include failures from heat cycling within the confined control area as well as moisture exposure over years of repetitive usage cycles. 

Symptoms of a bad main board include:

• The washer being unable to power on or begin cycles
• Error codes or flashing lights appearing on the display  
• Non-responsive buttons and improperly calibrated programming

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Console Assembly with Overlay is an OEM part for Frigidaire washing machines. Mounting to the top of the unit provides outer protection for the control panel and touchpad located behind.

Causes of failure are normal wear from repeated use and cleaning chemicals, as well as potential warping from prolonged heat and moisture exposure inside the unit.

Signs of a bad console assembly include:

• Broken, cracked, or improperly fitting outer overlay  
• Exposed internal padding or frame
• Loose, misaligned, or bubbled overlay veneer
• Faded or stained surfaces looking worn over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement drain hose for front-load washers. Connects the pump to the drain outlet. Replace if cracked, kinked, leaking, or damaged to restore drainage.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Secures wiring and hoses to your laundry center frame. Replace if cracked, broken, or missing to keep wire bundles organized and protected from wear.

Washer won't fill with water or only fills with cold? This water inlet valve controls water flow into the tub. DIY-friendly repair in about 30 minutes.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement indicator light for laundry center control panels. Restores visual feedback when panel lights fail or dim. Confirm fit with your model number.

This replacement cup funnels water to the ice maker fill tube and helps ensure proper water delivery for consistent ice production. It restores the fill path and prevents water from pooling where it can cause poor ice formation or leaks. What it does

• Directs water into the ice maker fill tube so molds receive the correct amount
• Helps prevent water from spilling into the ice bin or cabinet area
• Addresses symptoms like slow/weak ice production, water pooling under the ice maker, or visible leaks during a fill cycle
• Works with the ice maker assembly to maintain consistent ice size and formation

• One replacement ice-maker fill cup

• Disconnect power and shut off the water supply before servicing the ice maker
• Remove the ice maker or access panel per your model's service instructions to reach and replace the cup
• Handle plastic parts gently to avoid cracking; ensure a snug fit to prevent leaks
• If symptoms persist after replacement, check the fill valve and ice maker assembly for proper operation

A replacement drawer slide that helps the drawer open and close smoothly and stay aligned. Restores reliable sliding action for drawers that stick, sag, or catch while opening and closing. What it does:

• Guides and supports the drawer for smooth, even movement
• Prevents drawer sagging and misalignment during use
• Reduces sticking, scraping, or catching when opening or closing
• Helps maintain proper drawer fit and load distribution

What's included: One replacement slide Install notes:

• Disconnect power and remove drawer before replacing the slide
• Inspect mounting clips or screws and reuse or replace as needed; align slide before securing
• Use proper tools and avoid forcing parts to prevent damage

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.