Parts for Thermador DWHD410HPR/64: Control Panel Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fix a dishwasher that won't power on or reset with this on/off switch. Replaces worn or moisture-damaged switches. DIY-friendly installation.

The Door Latch is an OEM part for Bosch dishwashers. This latch ensures that the dishwasher door closes securely, allowing the appliance to operate correctly and safely by preventing water leaks and maintaining proper pressure during the wash cycle. The latch mechanism also signals to the control system that the door is securely closed, enabling the dishwasher to start.

Over time, the door latch can wear out or become damaged due to regular use or accidental impact. Common causes of a bad door latch include mechanical failure, wear and tear, or misalignment of the door.

Symptoms of a bad door latch include:

• The dishwasher door not staying closed
• The dishwasher not starting or stopping mid-cycle
• Water leaking from around the door during operation
• Error codes related to door closure issues

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Fix dishwasher control issues or erratic cycles with this cable harness. Connects control board to components. Moderate DIY repair in 30-45 minutes.

Dishwasher door frame assembly that secures outer and inner door panels. Replace if cracked, warped, or damaged, causing loose door fit or gaps.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

This holder is a molded mounting bracket that secures internal components and helps maintain proper alignment for reliable operation. It replaces a worn or broken support to restore fit and function. What it does:

• Secures and supports the associated component to prevent movement or misalignment
• Restores proper positioning when a cracked or broken bracket causes rattling or loose parts
• Helps reduce vibration and intermittent contact that can cause noise or poor performance
• Fits where the original molded holder has failed or become distorted

• Disconnect power and shut off water before replacing the part
• Remove access panels as needed to reach the mounting location; retain screws or clips for reassembly
• Align the holder with existing bosses or screw holes and secure with the original fasteners
• If clips or adjacent parts are damaged, inspect and replace as necessary for a secure fit

Replace your dishwasher's control panel button if it's cracked, broken, stuck, or missing. This button installs on the front control panel for operation.

Installation instructions for your dishwasher. Includes step-by-step guidance for proper setup and mounting. Replace if lost, damaged, or unclear.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.