Parts for Kitchenaid KESK901SBL01: 05 - Control Panel Parts

Fix a dual burner that won't heat or lacks proper temperature control. This infinite switch restores heat regulation for accurate simmer-to-boil cooking.

Burner won't heat or won't turn off? This infinite switch controls surface element temperature. DIY repair restores variable heat settings.

Fix a burner that won't heat or has no temperature control by replacing this 6-inch element switch. Restores smooth low-to-high heat adjustment in 30 minutes.

If your 8-inch burner won't heat, stays on high, or lost temperature control, this infinite switch is the fix. 30-minute DIY repair restores precision.

Range not responding to touchpad commands or display blank? This electronic control board manages cooking functions and cycle selections. Restores control.

Broken indicator light lens? This red lens covers the control panel light opening, restoring visibility and protection. Easy DIY fix in under an hour.

The Range Screw is an OEM part for Whirlpool ranges. It is a small but essential component used to secure various parts and panels of the range. It is designed to fit securely into pre-drilled holes, holding components tightly in place.

There are a few factors that can lead to a bad Range Screw. Over time, screws may become loose or stripped due to frequent use or inadequate tightening. Accidental cross-threading or overtightening can also damage the screw or the surrounding components.

Symptoms of a bad screw may include loose or wobbly parts, rattling noises during operation, or difficulty in keeping components securely attached. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Replace your range vent gasket to seal gaps and prevent heat loss around your oven vent. Install when torn, cracked, or no longer sealing properly.

Replace a worn, cracked, or missing range control knob. Fits onto the control shaft to provide manual adjustment of temperature and burner settings.

Replace your range's control knob if it's cracked, broken, or missing. This knob installs on the control panel to operate burners or oven settings.

Replace your range control knob when the original is cracked, stripped, or missing. This knob attaches to the control shaft for selecting settings.

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

Replacement mounting screw for securing panels and components. Install when original screw is stripped, missing, or damaged to prevent rattling.

Surface burner not heating or stuck on high? This range infinite switch controls cooktop element temperature. Common fix for heat control issues.

Fix a range burner that won't heat or turn off with this infinite switch. Common repair for burned out cooktop switches. Takes about 30 minutes to replace.

*** Note: Per factory, ribbon connector is part# WPW10237644

A replacement refrigerator door gasket that restores a tight seal to the fresh food compartment, helping maintain consistent temperatures and energy efficiency. Fits the factory channel for a direct seal replacement. What it does:

• Seals the fresh food door to prevent cold air loss and reduce temperature fluctuations
• Helps stop frost build-up, condensation, and excessive compressor run time
• Replaces torn, cracked, warped, or flattened seals that no longer seat properly
• Restores proper door closure and reduces energy waste

• Unplug the refrigerator or shut off power before beginning work
• Remove the old gasket and clean the door frame sealing surface before installing the new gasket
• Start by tucking the gasket into the channel at the corners, then work around the door so the gasket seats evenly
• If the gasket is stiff, gently warming with warm (not hot) water or allowing it to rest at room temperature can make installation easier