Parts for Ge GTW755CSM0WS: Controls & Backsplash Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Exterior decorative badge emblem that mounts to your washer cabinet or door. Replaces missing, faded, cracked, or detached emblems for a clean look.

Washer won't start or motor won't run? The start capacitor energizes the drive motor. Accessible repair requiring removal of electrical board.

Washer won't start or motor won't run? The start capacitor energizes the drive motor. Accessible repair requiring removal of electrical board.

This backsplash assembly kit replaces the rear panel on your range to protect the wall and improve appearance. It helps cover controls and contains the pieces needed to restore a finished, functional rear area. What it does:

• Replaces a cracked, dented, or missing backsplash to protect the wall from heat and cooking splatter
• Restores a clean, finished look behind the range and around controls
• Secures loose or rattling rear trim and prevents exposure of internal components
• Helps correct alignment and mounting where the original panel is bent or damaged

• Disconnect power (and gas, if applicable) before starting to avoid electrical or gas hazards
• Use basic hand tools; support the panel during removal/installation to avoid dropping or damaging surrounding parts
• Keep screws and small parts organized; inspect mounting points for damage before securing the new assembly

This left backsplash support secures the left side of a range or stove backsplash, keeping the backsplash aligned and stable for safe, reliable operation. It replaces a bent or broken support to restore proper fit and appearance. What it does:

• Holds and supports the left edge of the backsplash to prevent sagging or separation
• Restores proper alignment so control panels and trim sit flush
• Helps stop rattling or vibration caused by a damaged support
• Commonly replaced when the support is bent, cracked, or missing

• Install with the appliance unplugged and controls off; disconnect power at the breaker for electric ranges.
• Depending on model, you may need to remove the backsplash trim or rear panel to access mounting points.
• Use correct-size fasteners and verify secure attachment; avoid overtightening to prevent cracking.

This right-side backsplash support secures the range's backsplash to the cooktop, restoring proper alignment and stability so the backguard sits firmly and reduces wobble or gaps. Designed to fit the OEM mounting points. What it does

• Holds the right side of the backsplash in place so the backguard stays aligned with the cooktop
• Prevents the backsplash from leaning, rattling, or separating from the range
• Restores proper mounting after impact, wear, or missing/broken fasteners
• Works with the range's existing screws and mounting brackets to re-establish a solid fit

• One right-side backsplash support

• Disconnect power to the appliance before starting any repair
• Remove the backguard or access panel per manufacturer instructions to reach mounting area
• Use basic hand tools (screwdriver/socket) to remove and replace fasteners; keep original screws if reusable
• Watch for sharp sheet-metal edges and wear safety gloves and eye protection

This knob assembly replaces a worn, broken, or missing control knob so you can reliably select heat or settings on your range or cooktop. It restores safe, accurate user control and a finished appearance. What it does:

• Fits onto the control shaft to allow turning the switch for burner/oven settings
• Restores tactile grip and clear position selection when the original had stripped or cracked
• Helps stop slipping or intermittently losing contact between the user and the control
• Suitable for use where the original knob assembly is damaged or missing

• Disconnect power (or turn off gas appliance supply) before servicing controls.
• Push the knob straight onto the control shaft until fully seated; pull straight off to remove.
• Inspect the switch/shaft for damage; replace the switch or shaft if the knob does not seat securely.

The User Interface and Control Board with WiFi is an OEM part for GE washing machines. As the central processing unit, it operates all wash cycle and programming functions while enabling WiFi connectivity for remote start capabilities.

Causes of failure can include moisture damage compromising electrical components, short circuits from age or excessive wear/stress, or incompatibility issues preventing communication between newer interfaces and older machines.

Symptoms include: 

• Fault codes displayed 
• Non-responsive buttons and displays
• Inability to start or stop cycles remotely 
• Failure to advance through wash phases

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models featuring WiFi home connectivity.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix washer electrical failures with this jumper harness. Restores connector-to-connector wiring between components when original harness is worn or damaged.

Rear housing panel for washer control assembly. Mounts behind the main control panel to provide structural support. Replace if cracked, broken, or damaged.

8-18 hi/lo 5/8

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Fastens panels, brackets, and trim to appliance cabinets. Replace this screw when the original is missing, stripped, or damaged during service work.

Fix a washer that won't start or has a blinking lid lock light with this lid lock wiring harness. Connects the lid lock to the control board. Easy DIY fix.

Power cord for top-load washers. Connects washer to wall outlet to supply electricity. Replace if cord is frayed, damaged, or prongs are worn or bent.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.